Epson FX 890 제품 정보 매뉴얼 - 페이지 12

{카테고리_이름} Epson FX 890에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson FX 890 19 페이지. Impact printer
Epson FX 890에 대해서도 마찬가지입니다: 사양 시트 (1 페이지), 사용자 설명서 (48 페이지), 사양 (2 페이지), 매뉴얼 (11 페이지), 설정 매뉴얼 (2 페이지), 빠른 참조 (12 페이지), 사양 (2 페이지)

페이지 인쇄

Using the Micro Adjust Function

The Micro Adjust function allows you to move the paper

forward or backward in 1/216-inch (0.118 mm) increments to

adjust the tear-off and top-of-form positions.

Adjusting the Tear-off Position

If your paper's perforation is not aligned with the tear-off edge,

you can use the Micro Adjust function to move the perforation

to the tear-off position. Your tear-off position setting remains in

effect until you change it, even if you turn off the printer.

Caution: Never use the knob to adjust the tear-off position; this may

damage the printer or cause it to lose the tear-off position.

1. Make sure the Tear Off/Bin light is flashing (the paper is at

the current tear-off position). You may need to press the

button to advance the paper to the tear-off

Tear Off/Bin

position.

2. Hold down the

Pause

Pause light begins flashing and the printer enters Micro

Adjust mode.

3. Open the paper guide cover and press

paper backward, or

Load/Eject

until the paper perforation is aligned with the tear-off edge

of the printer cover.

Note: The printer has a minimum and a maximum tear-off

position. If you try to adjust the position beyond these limits, the

printer beeps and stops moving the paper.

button for about three seconds. The

D to feed

LF/FF

U to feed paper forward,

tear-off edge

paper

perforation

4. Tear off the printed pages.

5. Press the

button to turn off Micro Adjust mode.

Pause

When you resume printing, the printer automatically feeds the

paper back to the top-of-form position and begins printing.

Adjusting the Top-of-form Position

The top-of-form position is the position on the page where the

printer starts printing. If your printing appears too high or low

on the page, you can use the Micro Adjust function to adjust

the top-of-form position, as described below. Your top-of-form

position setting remains in effect until you change it, even if you

turn off the printer.

Caution: Never use the knob to adjust the top-of-form position; this

may damage the printer or cause it to lose the top-of-form position.

1. Make sure the printer is turned on.

2. Load paper. (If the tractor is in a push position, press the

button to advance continuous paper to the

Load/Eject

current top-of-form position.) If necessary, lift up the

printer cover so you can see the paper position.

3. Hold down the

Pause

light flashes and the printer enters Micro Adjust mode.

4. Press the

D button to move the top-of-form position

LF/FF

up on the page, or press the

the top-of-form position down on the page.

5. Press the

button to exit Micro Adjust mode.

Pause

Note: The printer has a minimum and a maximum top-of-form

position. If you try to adjust it beyond these limits, the printer

beeps and stops moving the paper.

When the paper reaches the default top-of-form position, the

printer beeps and stops moving the paper briefly. You can use

this setting as a reference point when adjusting the position.

The top margin setting made in some software overrides the

top-of-form position setting you make with the Micro Adjust

function.

6/03

EPSON FX-890/FX-2190

button for three seconds. The Pause

U button to move

Load/Eject

EPSON FX-890/FX-2190