Epson FX-2190 제품 정보 매뉴얼 - 페이지 16

{카테고리_이름} Epson FX-2190에 대한 제품 정보 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson FX-2190 19 페이지. Impact printers
Epson FX-2190에 대해서도 마찬가지입니다: 사용자 설명서 (48 페이지), 사양 (2 페이지), 매뉴얼 (11 페이지), 설정 매뉴얼 (2 페이지), 사양 (2 페이지), 빠른 참조 (12 페이지), 여기에서 시작 (2 페이지)

페이지 인쇄

Follow the steps below to enter the default-setting mode. You'll

need four sheets of A4 or letter size single-sheet paper or four

pages of continuous paper that is at least 11 inches (279 mm)

long and 8.3 inches (210 mm) wide. If you use single sheets,

you need to load a new sheet of paper each time the printer

ejects a printed sheet from the paper guide.

1. Make sure the printer is on and paper is loaded. Then press

the

and

Pitch

Tear Off/Bin

Menu lights (both the Tear Off/Bin lights) turn on, and the

printer enters the default-setting mode and prints the

language selection instructions.

2. Press the

button until the Font lights show the

Font

language you want, as described in the instructions.

3. Press the

Tear Off/Bin

mode instructions (three pages) in the language you

selected. The printed instructions list the settings you can

change, describe how to change them, and show how the

control panel lights help you make settings. Use these

instructions to change the printer's default settings from the

control panel.

4. When you finish making settings, press the

(

and

Pitch

Tear Off/Bin

buttons to open the Menu. The

button to print the default-setting

) to exit the default-setting mode.

Emulating the Okidata Microline 320/

321 Turbo

You can make your FX-890 or FX-2190 work like the Okidata

Microline

printer emulates Okidata functions, and the following

additional settings can be selected in the default setting mode.

The default settings (shown in bold) are consistent with

Okidata Microline 320/321 Turbo factory settings.

Feature

Software emulation

Auto tear off wait time

Bottom margin

Line spacing

(lines per inch)

Paper out override

Note: The FX-890 and FX-2190 do not support the USB interface in

Okidata mode.

If you want to use your printer in Okidata mode, do not install

buttons

the Windows driver that came with your printer. If you have

been using an Okidata driver, you can continue to use it with

your printer in Okidata mode.

If you have been using an Okidata printer, you may want to

print out its default settings for reference before changing

modes on the FX-890/FX-2190. To do this on the Okidata

printer, press

To enter Okidata mode on your FX-890/FX-2190, make sure

the printer is turned off. Then hold down the

buttons while you turn on the printer. The printer beeps

Pause

once to indicate it is now in Okidata mode. It remains in

Okidata mode until you repeat the above procedure. To return

to FX-890/FX-2190 mode, hold down the

buttons while you turn on the printer. The printer beeps

Pause

twice and is now operating in FX-890/2190 mode.

When you switch from one mode to the other, any changes you

made to the printer's settings in the original mode are restored

to their default values. You can print the default settings for the

printer to check the current settings and change them if

necessary. See page 14.

6/03

EPSON FX-890/FX-2190

320 Turbo or 321 Turbo. In Okidata mode, the

Printer settings in Okidata mode

IBM PPDS, EPSON ESC/P, Oki ML 320T

0.5 second, 1 second, 2 seconds, Others

4.2 mm, 20 mm, 22 mm, 24 mm, Others

6 LPI, 8 LPI

Off (No), On (Yes)

to enter Menu mode, and then press

SHIFT + SEL

EPSON FX-890/FX-2190

and

Tear Off/Bin

and

Tear Off/Bin