Dimplex BF33DXP 서비스 매뉴얼 - 페이지 4

{카테고리_이름} Dimplex BF33DXP에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dimplex BF33DXP 20 페이지. Fireplace
Dimplex BF33DXP에 대해서도 마찬가지입니다: 실용적인 사용자 설명서 (15 페이지), 소유자 매뉴얼 (14 페이지), 사용자 설명서 (14 페이지), 문제 해결 매뉴얼 (2 페이지), 소유자 매뉴얼 (14 페이지), 설치 매뉴얼 (14 페이지)

페이지 인쇄

Level 1 - Flame effect only, twice activates Level 2 -

Flame effect and Purifire™, three times activates Level

3 - Flame effect, Purifire™ and heat.

C . On Button

Pressing this button at any time will shut the unit off.

D, E & F LED Indicators

Depicts which of the three (3) levels the fireplace is

currently operating at: Level 1 -

3 -

Optional Remote Control Operation

The BFRC-KIT is supplied with a radio frequency remote

control. This remote control has a range of approximately

50 feet (15.25 m), it does not have to be pointed at the

fireplace and can pass through most obstacles (including

walls). It is supplied with one of hundreds of independent

frequencies to prevent interference with other units.

NOTE: Before attempting any operation with the

remote, pull the plastic insulator strip out from between

the remote casing and battery cover (Figure 3).

The remote control operates the fireplace levels

sequentially. The level is increased every time the ON

button on the remote control is pressed. The fireplace can

be turned off at any point by pressing the OFF button on the

remote control.

NOTE: The Mode Selector Switch on the original

manual controls needs to be set to "=" to have full

functionality of the fireplace. (Figure 2)

Level 1

:The flame effect is turned on and the first red

indicator light is activated.

Level 2

: The flame effect remains on, the Purifire is

activated. (Heater remains off)

Level 3

: The flame effect remains on, the Purifire is

activated and the heater turns on.

Remote Control Initialization/Reprogramming

If the remote control or receiver has been replaced or the

remote does not seem to be operating the fireplace, follow

these steps to initialize/reprogram the remote control and

receiver:

Ensure that power is supplied through main service

panel.

Figure 3

Button

Off Button

Plastic

Strip

Battery

Cover

, Level 2 -

or Level

Battery must

be recycled or

disposed of

properly. Check with

your Local Authority or

Retailer for recycling

advice in your area.

Access the manual controls, (remove the glass doors

if applicable) pull the right hand steel curtain to the

outside of the unit.

Locate manual controls.

Move the 3-position switch to "Remote", on newer

models only.

Activate the main power switch, the red Level 1

Indicator Light may flash

Press and hold the On button on the manual controls

(Figure 2-C) for five (5) seconds. The Level 1 Indicator

Light

(Figure 2-D) will then flash for 10 seconds.

7 .

Within

the 10 seconds press the ON button located on

the hand held remote control (Figure 3) or any button

on the wall mounted controller. This will synchronize

the remote control and receiver.

Battery Replacement

To replace the battery:

Slide battery cover open on the remote control

(Figure 3).

Install one (1) 12-Volt (A23) battery in the battery

holder.

Close the battery cover.

Optional Wall Mounted Remote Operation

NOTE: For button/display references see Figure 4.

1 . Room Temperature - Displays current ambient

temperature in the room.

2 . Set Temperature - Displays and controls the heater

to the temperature at which the thermostat is currently set

to. Press 8 to lower the thermostat and press 9 to raise

the thermostat. Pressing both 8 and 9 together will toggle

between Celsius and Fahrenheit.

3 . Flame Effect Icon - The flame icon will flicker if and

when the Flame Effect is turned on. Press 11 to turn the

Flame Effect on, and press 10 to turn the Flame Effect off.

4. Purifire™ Icon - The display arrows for the Purifire™

will cycle when turned on. Press 13 to turn the Purifire™

function on, and press 12 to turn Purifire™ off.

5 . heat Off Indicator - This function manually overrides

the thermostat control and prevents the fireplace's heater

from coming on.

To do this, press 8 to decrease Set Temperature to any

temperature below 0

C or 32

"hEAT OFF" setting, press 9 to increase the thermostat

Set Temperature. The Set Temperature will be displayed

starting at 21

C (70

F), replacing the "hEAT OFF" icon.

6 . Function Lock Indicator - Enabling this function will

lock out the Wall Switch Remote Control so as to prevent

the current settings from being changed. To Enable, press

8, 9, and 10 sequentially. To disengage, press 8, 9 and

10 sequentially again. The Indicator icon will be displayed

when enabled.

7 . RF Code Function and Change Procedure - In

. (Figure 2-D)

F. To reactivate heat from