Dimplex BF33STP 서비스 매뉴얼 - 페이지 3

{카테고리_이름} Dimplex BF33STP에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dimplex BF33STP 20 페이지. Fireplace
Dimplex BF33STP에 대해서도 마찬가지입니다: 실용적인 사용자 설명서 (15 페이지), 소유자 매뉴얼 (14 페이지), 사용자 설명서 (14 페이지), 문제 해결 매뉴얼 (2 페이지), 소유자 매뉴얼 (14 페이지), 설치 매뉴얼 (14 페이지)

페이지 인쇄

OPERATION

Manual Controls - Without Remote Option

The fireplace can be controlled by the manual switches

located on the fireplace (Figure 1).

Figure 1

Voltage Selector Switch

Over Heat Indicator

Main On/Off Switch

Main Power Switch - Energizes firebox and flame.

Mode Selector Switch:

Select "o" for flame only

Select "-" for Purifire™/flame (no heat)

Select "=" for heat/Purifire™/flame

Voltage Selector Switch

WARNINg: Ensure that the incoming power supply

voltage matches the setting of the voltage selector

switch.

NOTE: The voltage selector switch is located inside

the exhaust panel on the top right hand corner (Figure

1).

CAUTION: When changing the voltage selector switch

from 240 volts to 120 volts ensure that the power supply

is turned off.

NOTE: Carefully insert a flat head screwdriver inside

the exhaust panel to change the switch from 240 volts

(230 position) to 120 volts (115 position).

Resetting the Temperature Cutout Switch

The heater on this fireplace is protected with a safety device

to prevent overheating. Should the heater overheat, a red

light (Figure 1) will be activated and an automatic cut out

will turn the heater off. The heater will re-activate once the

heater has cooled. The overheat cutout will be triggered if

the filter is dirty.

CAUTION: If you need to continuously reset the heater,

disconnect power and call Dimplex customer service at

1-888-DIMPLEX (1-888-346-7539).

Mode Selector Switch

Manual Controls - With Remote Accessory

(hand held or Wall Mounted)

The fireplace with the Remote Option has the same manual

controls with the addition of the Remote Control Receiver

(BFRC-KIT). The Remote Receiver Switch Board which will

work in conjunction with the original controls.

The remote control operation can be adjusted, depending

on the season and desired effects, by toggling the main

mode selector switch built into the fireplace. The position

of the switch will dictate the available functions that the

remote control will cycle through.

NOTE: The original controls will override all other

settings, both the Mode Selector Switch as well as the

Main On/Off Switch. (Figure 2)

A . Manual Selection Switch

Switches the operation of the fireplace between the

different modes of the fireplace:

•

OFF (center): Makes the unit inoperable.

•

MANUAL (top): All functions of the fireplace are

controlled by the On and Off buttons as described above

(Figure 2B & C).

•

REMOTE (bottom): All functions of the fireplace are

controlled by the Remote Control.

B . Off Button

Pressing this button toggles sequentially through the three

levels of the fireplace. (Only when the selection switch is in

the Manual Position)

•

Mode Selector Set at "O": Only Flame Effect at all 3

levels.

•

Mode Selector Set at "--": Pressing once activates

Level 1 - Flame effect only, two and three times

activates Level 2 - Flame effect and Purifire™.

•

Mode Selector Set at "=": Pressing once activates

Figure 2

Original Version

2010 Update