Epson PowerLite 1825 사용자 설명서 - 페이지 35

{카테고리_이름} Epson PowerLite 1825에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson PowerLite 1825 42 페이지. Release of check tool for network projectors v1.00 for windows
Epson PowerLite 1825에 대해서도 마찬가지입니다: 운영 매뉴얼 (36 페이지), 빠른 설정 (2 페이지), 운영 매뉴얼 (47 페이지), 적합성 선언 (4 페이지), 사용자 설명서 (14 페이지), 제품 사양 (2 페이지), 부품 목록 (1 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (42 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (34 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

페이지 인쇄
Epson PowerLite 1825 사용자 설명서

E-mail notification function settings

E-mail notification function settings
The mail notification function can be used to send corresponding
notification messages to a preset e-mail address when a projector that is
connected to the network assumes a certain status, or if it experiences a
problem or warning. By using this function, the operator can be notified
of a projector's status or problems even when the operator is in a
different location from the projectors.
• Up to three addressees (destinations) can be registered and messages
can be sent to all of them at once.
• If a critical problem develops with a projector which causes it to
suddenly stop working, it may not be possible for the projector to send
a message notifying an operator of the problem.
• If Standby Mode is set to Network ON or Network Monitoring is set to
ON in the projector configuration menus, you can monitor the
projector even when it is in standby mode (when its power is turned
off). s Projector User's Guide
• On some projectors, the mail notification function can be set in the
configuration menu. When notification messages are set to be sent in
the projector's configuration menu, both the settings in the
configuration menu and settings made on EMP Monitor are
functional.
• Detectable status with the mail notification function differs with the
projector you are using.
Procedure
A
Select "Mail notification function" from the Tool menu.
B
The Set mail notification function window will be displayed.
Make the necessary settings while referring to the table below.
Mail notification
Set to ON to use the mail notification function.
function
SMTP server IP
Enter the IP address of the SMTP server. Up to
address
a maximum of 255 bytes can be entered.
When you change a port number of the SMTP
server, specify this port number. The default
value is "25".
You can enter a valid number from 1 to 65535.
Sender mail
Enter the sender's e-mail address. Up to a
address
maximum of 255 bytes can be entered.
Recipient mail
Specify the destination addresses for the
address 1
notification e-mail. Up to three destinations
can be set. Up to a maximum of 255 bytes can
Recipient mail
be entered.
address 2
Recipient mail
address 3
35