Dimplex BLF50 서비스 매뉴얼 - 페이지 3
{카테고리_이름} Dimplex BLF50에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dimplex BLF50 16 페이지.
Dimplex BLF50에 대해서도 마찬가지입니다: 서비스 매뉴얼 (19 페이지)
페이지 인쇄
OPERATION
The BLF50 operates in a 3-Stage process. These
stages can be controlled either by the remote control
or by the manual controls which are located on the
right side of the unit and inside the air intake slot
(Figure 1).
Figure 1
C
Manual Controls
A . Main On/Off Switch
The Main On/Off Switch supplies power to all fireplace
functions. When the switch is in the " I " position, the unit is
on. When in the " O " position, the fireplace is off.
B . Three Position Switch
The Three Position Switch changes the mode the fireplace
operates in and has three (3) positions: " MANUAL "; " OFF
"; and " REMOTE ".
When in " REMOTE " mode, the fireplace's three levels of
operation are controlled by the ON and OFF buttons of the
remote control transmitter.
In " OFF " mode, power to all functions is cut off.
In " MANUAL " mode, the fireplace's three levels of
operation are controlled by the Manual Control Buttons.
C . Manual Control Buttons
The Manual Control Buttons operate the fireplace levels
sequentially (from off): flames only; to flames and low heat;
to flames and high heat.
The level is increased every time the " I " button is pressed,
and the fireplace can be turned off at any point by pressing
the " O " button.
Resetting the Temperature Cutoff Switch
Should the heater overheat, an automatic cut out will turn
the fireplace off and it will not come back on without being
reset. It can be reset by switching the Main On/Off Switch
to Off and waiting five (5) minutes before switching the unit
back on.
CAUTION: If you need to continuously reset the heater,
disconnect power and call Dimplex customer service at
1-888-DIMPLEX (1-888-346-7539).
A
B
Remote Control
The fireplace is supplied with a radio frequency remote
control. This remote control has a range of approximately
50 feet (15.25 m), it does not have to be pointed at the
fireplace and can pass through most obstacles (including
walls). It is supplied with one of hundreds of independent
frequencies to prevent interference with other units.
!
NOTE: Before attempting any operation with the
remote, pull the plastic insulator strip out from between
the remote casing and battery cover (Figure 2).
Remote Control Initialization/Reprogramming
If the hand held transmitter or receiver board has been
replaced, follow these steps to initialize the transmitter and
receiver:
1.
Ensure that power is supplied through the main service
panel.
2.
Turn Main On/Off Switch to On (Figure 1A).
3.
Move the Three Position Switch to the
position (Figure 1B).
4.
Press and hold the Manual Control Button marked
(Figure 1C) for five (5) seconds. After five (5) seconds,
there is a 10 second window to press any button on the
remote control.
5 .
Within
10 seconds press any button on the remote
control transmitter. If the unit does not initialize, turn the
main power switch off for 30 seconds and try starting at
Step 1.
This will synchronize the remote control transmitter and
receiver.
Remote Control Usage
The remote control operates the fireplace levels
sequentially (from off): flames only; to flames and low heat;
to flames and high heat.
The level is increased every time the ON button is pressed
on the remote control transmitter and the fireplace can be
turned off at any point by pressing the OFF button.
Battery Replacement
To replace the battery:
1.
Slide battery cover open on the hand held transmitter
(Figure 2).
2.
Install one (1) 12-Volt (A23) battery in the battery
holder.
3.
Close the battery cover
Figure 2
On
Button
Off Button
Plastic
Strip
Battery
Cover
" REMOTE "
" I "
Battery must
be recycled or
disposed of
properly. Check with
your Local Authority or
Retailer for recycling
advice in your area.
3