Epson PowerLite 1825 제품 지원 게시판 - 페이지 32

{카테고리_이름} Epson PowerLite 1825에 대한 제품 지원 게시판을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson PowerLite 1825 34 페이지. Release of check tool for network projectors v1.00 for windows
Epson PowerLite 1825에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 빠른 설정 (2 페이지), 운영 매뉴얼 (47 페이지), 적합성 선언 (4 페이지), 사용자 설명서 (14 페이지), 제품 사양 (2 페이지), 부품 목록 (1 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (12 페이지), 제품 지원 게시판 (42 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (38 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

Q3.

Can I use USB flash memory where the update file is saved with other files?

A3.

We recommend you use a USB flash memory with only update files.

Q4.

What do the projector's LED status indicators mean?

A4.

1 USB access indicator shows a solid orange. (Accessing USB memory)

2 USB access indicator shows a solid green. (Preparing update)

3 Power, Lamp and Temp indicators of the projector show a solid orange. (Download

mode)

4 USB access indicator shows a solid green again. (System updating)

5 After the solid green of the USB access indicator and the solid orange of

Power/Lamp/Temp indicators of the projector go off, the power indicator exhibits solid

orange and then the projector enters standby mode.

Note: A solid red of the USB access indicator means that the update failed abnormally.

Q5.

A5.

Please turn off the projector and retry the update procedure starting from step 1 above.

Possible causes of the failure

If you change the name of the update file in the root directory of USB flash memory,

insert the USB memory in the projector and start the update, a black screen with a

message "no file" is displayed. When the message is displayed, the firmware cannot

be upgraded.

When the root directory of USB flash memory doesn't have the update files in it, the

update cannot be executed.

Q6.

What does it mean when the projection screen keeps showing the message

"Starting EasyMP" on blue background, and cannot be shifted to EasyMP screen?

A6.

If you observe this issue, it may be an indication that the upgrade has failed. You may

attempt to perform the upgrade again, but is some cases the firmware upgrade will

continue to fail and the projector will be unusable. In this case, please contact Epson End

User Technical support at 1-562-276-4394 or a local Epson Authorized Customer Care

Center.

Q7.

Do you have a list of known good or bad USB memory devices that have been

tested?

A7.

Yes, below is a short list of USB flash memory devices that we have tested. If your USB

memory device is not in the list, it may still work, however it has not been tested. When

using an untested USB memory device, please watch for the symptoms or behavior

described in the comments section below.

Page 4 of 5

PSB.2007.06.002