Epson PowerLite 9300i - PowerLite 9300NL Multimedia Projector 빠른 매뉴얼 - 페이지 6

{카테고리_이름} Epson PowerLite 9300i - PowerLite 9300NL Multimedia Projector에 대한 빠른 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson PowerLite 9300i - PowerLite 9300NL Multimedia Projector 20 페이지. Release of emp ns connection for windows & mac upgrade from v2.50 to v2.51
Epson PowerLite 9300i - PowerLite 9300NL Multimedia Projector에 대해서도 마찬가지입니다: 사용자 설명서 (42 페이지), 운영 매뉴얼 (36 페이지), 브로셔 및 사양 (2 페이지), 운영 매뉴얼 (47 페이지), 제품 지원 게시판 (27 페이지), 빠른 설정 (2 페이지), 교체 부품 (1 페이지), 제품 지원 게시판 (25 페이지), 제품 지원 게시판 (22 페이지), 제품 지원 게시판 (28 페이지), 제품 지원 게시판 (41 페이지), 제품 지원 게시판 (15 페이지), 제품 지원 게시판 (22 페이지)

페이지 인쇄
Epson PowerLite 9300i - PowerLite 9300NL Multimedia Projector 빠른 매뉴얼
EPSON PowerLite 9300i Projector

Displaying an Image

If you turn on your computer or video equipment before
turning on the projector, the projector will automatically
select the connected source. If you have multiple sources
connected, you may have to switch to the desired source
manually (see "Selecting the Image Source" at right).

Turning On the Projector

1. Remove the lens cap.
Caution: Do not use the projector with the lens cap in place.
The heat generated by the lens can damage the cap.
2. Connect the power cord to the projector, then plug the
other end into a grounded electrical outlet.
3. Wait a few seconds until the P power light to turns orange.
4. Press the red P
Power
can also use the P
Power
Power
button
If you're using the remote control, make
sure batteries are installed and the power
switch on the side of the remote control
is turned on.
The P power light flashes green as the
projector warms up, and an image begins
to appear after about 30 seconds. When the power light
stops flashing and remains green (in about 40 seconds), the
projector is ready for use.
If you've enabled password protect, enter your password at
the prompt.
Warning: Never look into the lens when the lamp is on. This
can damage your eyes.
Note: To shut down the projector, see page 10. Shutting
down the projector correctly prevents premature lamp failure
and possible damage from overheating.
6
EPSON PowerLite 9300i Projector
-
button on top of the projector. You
button on the remote control.

Selecting the Image Source

You can use the source buttons either on the projector or the
remote control:
The projector has two
Use the
Computer/DVI
equipment connected to the Computer 1, Computer 2, and
DVI ports.
Use the
Video/BNC
connected to the Video, S-Video, and BNC ports.
The remote control has seven
switch between equipment connected to the port identified
on each button.
Note: You can preview all sources to help you select the desired
source (see page 7).
10/03
buttons.
Source
button to switch between
button to switch between equipment
buttons. Use them to
Source