Toshiba 20AS21 서비스 매뉴얼 - 페이지 12

{카테고리_이름} Toshiba 20AS21에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Toshiba 20AS21 31 페이지. Toshiba 20as21: owners manual
Toshiba 20AS21에 대해서도 마찬가지입니다: 소유자 매뉴얼 (9 페이지)

페이지 인쇄
Toshiba 20AS21 서비스 매뉴얼
2-6: HORIZONTAL PHASE
1.
Receive the center cross signal from the Pattern
Generator.
2.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (05) on the remote control to
select "H PHASE".
3.
Press the VOL. UP/DOWN button on the remote
control until the SHIFT quantity of the OVER SCAN on
right and left becomes minimum.
2-7: VERTICAL SIZE
NOTE: Adjust after performing adjustments in section 2-6.
1.
Receive the crosshatch signal from the Pattern
Generator.
2.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (06) on the remote control to
select "V SIZE".
3.
Press the VOL. UP/DOWN button on the remote control
until the rectangle on the center of the screen becomes
square.
4.
Receive a broadcast and check if the picture is normal.
2-8: VERTICAL SHIFT
NOTE: Adjust after performing adjustments in section 2-7.
1.
Receive the crosshatch signal from the Pattern
Generator.
2.
Activate the adjustment mode display of Fig. 1-1
and press the channel button (07) on the remote control
to select "V SHIFT".
3.
Press the VOL. UP/DOWN button on the remote
control until the horizontal line becomes fit to the notch
of the shadow mask.
ELECTRICAL ADJUSTMENTS
"A"
Fig. 2-1
0%
120%
100%
Fig. 2-2
2-9: OSD HORIZONTAL
1.
Activate the adjustment mode display of Fig. 1-1.
2.
Press the VOL. UP/DOWN button on the remote
control until the difference of A and B becomes
minimum. (Refer to Fig. 2-3)
00 OSD
A
2-10: VIF VCO
1.
Place the set with Aging Test for more than 10 minutes.
2.
Receive an 80dB monoscope pattern.
3.
Connect the digital voltmeter between the pin 5 of
CP601 and the GND.
4.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (03) on the remote control to
select "VIF VCO".
5.
Press the VOL. UP/DOWN button on the remote control
until the digital voltmeter is 2.5V.
2-11: SUB CONTRAST MANUAL
1.
Receive a 70dB the color bar pattern. (RF Input)
2.
Activate the adjustment mode display of Fig. 1-1
press the channel button (14) on the remote control to
select "CONTRAST".
3.
Press the VOL. UP/DOWN button on the remote control
until the contrast step No. becomes "100".
4.
Receive a 70db the color bar pattern. (Audio Video Input)
5.
Press the TV/VIDEO button on the remote control
to set to the AV mode. Then perform the above
adjustments 2~3.
2-12: BRIGHTNESS
1.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (13) on the remote control to
select "BRIGHTNESS".
2.
Press the VOL. UP/DOWN button on the remote control
until the brightness step No. becomes "136".
3.
Press the TV/VIDEO button on the remote control to set
to the AV mode. Then perform the above adjustments
1~2.
TV
15
B
Fig. 2-3