Toshiba 24 WD3A Series 사용 설명서 - 페이지 9

{카테고리_이름} Toshiba 24 WD3A Series에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Toshiba 24 WD3A Series 45 페이지.
Toshiba 24 WD3A Series에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (9 페이지), 사용 설명서 (38 페이지), 사용 설명서 (37 페이지), 사용 설명서 (37 페이지)

페이지 인쇄

the preferences for deleting the recordings in order

to obtain more storage space for ongoing records.

Hard disk information: You can view detailed

information about the USB storage device connected

to your TV. Highlight and press OK to see and press

Back/Return to close.

Format Disk: If you want to delete all files on the

connected USB storage device and convert the disk

format to FAT32, you can use this option. Press OK

button while the Format Disk option is highlighted.

A menu will appear on the screen, requiring you

to enter the PIN(*). After you enter the PIN, a

confirmation message will be displayed. Select Yes

and press OK to start formatting the USB storage

device. Select No and press OK to cancel.

(*) Default PIN could have been set to 0000 or 1234. If you

have defined the PIN(is requested depending on the country

selection) during the First Time Installation use the PIN

that you have defined.

3. Settings

You can manage the settings of your TV using the op-

tions of this menu. Refer to Settings Menu Contents

section for more information.

4. Apps

When your TV is connected to the Internet related

contents will also be available, including Apps related

contents. Using the Apps menu you can access and

manage your applications. You can add new apps from

the market or delete the existing ones. Refer to Apps

section for more information.

5. Source

You can manage your input source references using

the options of this menu. To change the current source

highlight one of the options and press OK.

5.1. Source Settings

Edit the names, enable or disable selected source

options.

Inserting the Batteries into the Remote

Remove the back cover to reveal the battery

compartment. Insert two size AAA batteries. Make

sure the (+) and (-) signs match (observe correct

polarity). Do not mix old and new batteries. Replace

only with same or equivalent type. Place the cover back

on. A message will be displayed on the screen when

the batteries are low and must be replaced.

Note that when the batteries are low, the performance

of the remote control may be impaired.

Power Connection (**)

IMPORTANT: The TV set is designed to operate on a

220-240V AC, 50 Hz supply. After unpacking, allow the

TV set to reach the ambient room temperature before

you connect the set to the mains.

Plug one end (the two-hole plug) of the supplied

detachable power cord into the power cord inlet on

the rear side of the TV as shown above. Then plug

the other end of the power cord into the mains socket

outlet.

Note: The position of the power cord inlet may differ depending

on the model.

Power Connection (**)

IMPORTANT: The TV set is designed to operate on a

220-240V AC, 50 Hz supply. After unpacking, allow the

TV set to reach the ambient room temperature before

you connect the set to the mains. Plug the power cable

to the mains socket outlet.

Antenna Connection

Connect the aerial or cable TV plug to the AERIAL

INPUT (ANT.) socket or satellite plug to the SATELLITE

INPUT (LNB) socket located on the rear side of the TV.

Rear side of the TV

Satellite

Aerial or cable

If you want to connect a device to the TV, make sure

that both the TV and the device are turned off before

making any connection. After the connection is done,

you can turn on the units and use them.

English - 8 -

(**) Limited Models Only