Toshiba DIGITAL Series 소유자 매뉴얼 - 페이지 3

{카테고리_이름} Toshiba DIGITAL Series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Toshiba DIGITAL Series 4 페이지. Split type
Toshiba DIGITAL Series에 대해서도 마찬가지입니다: 소유자 매뉴얼 (48 페이지), 사용자 설명서 (45 페이지), 사용자 설명서 (49 페이지), 소유자 매뉴얼 (50 페이지), 사용자 설명서 (48 페이지), 소유자 매뉴얼 (41 페이지), 소유자 매뉴얼 (22 페이지), 설치 참고 사항 (4 페이지)

페이지 인쇄

TEMPORARY OPERATION

In case of the misplaced or discharged remote control

• Pressing the RESET button, the unit can start or stop

without using the remote control.

• Operation mode is set on AUTOMATIC

operation, preset temperature is 24°C

and fan operation is automatic speed.

TIMER OPERATION

Setting the ON Timer

Press

: Set the desired ON timer.

Press

: Set the timer.

SET

Press

: Cancel the timer.

CLR

Everyday timer allows the user to set both the ON & OFF timers and will be activated on a daily basis.

Setting Everyday Timer

Press

: Set the ON timer.

Press

OFF

: Set the OFF timer.

• During the every day timer is activating, both arrows ( , ) are indicated.

Note:

• Keep the remote control in accessible transmission to the indoor unit;

otherwise, the time lag of up to 15 minutes will occur.

• The setting will be saved for the next same operation.

PRESET OPERATION

Set your preferred operation for future use. The setting will be memorized by the

unit for future operation (except airﬂ ow direction).

1. Select your preferred operation.

PRESET

for 3 seconds to memorize the setting. The P mark

2. Press and hold

displays.

PRESET

3. Press

: Operate the preset operation.

AUTO RESTART OPERATION

To automatically restart the conditioner after the power failure (Power of the unit

must be on.)

Setting

1. Press and hold the RESET button on the indoor unit for 3 seconds to set the

operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5 seconds)

• Do not operate ON timer and OFF timer.

2. Press and hold the RESET button on the indoor unit for 3 seconds to cancel the

operation. (3 beep sound but OPERATION lamp does not blink)

QUIET OPERATION

To operate at super low fan speed for quiet operation (except in DRY mode)

QUIET

Press

: Start and stop the operation.

Note: Under certain conditions, QUIET operation may not provide adequate

cooling or heating due to low sound features.

COMFORT SLEEP OPERATION

To save energy while sleeping, automatically control air ﬂ ow and automatically

turn OFF.

COMFORT

SLEEP

Press

: Select 1, 3, 5 or 9 hrs for OFF timer operation.

Note: The cooling operation, the set temperature will increase automatically

1 degree/hour for 2 hours (maximum 2 degrees increase). For heating

operation, the set temperature will decrease.

SLEEP TIMER OPERATION

To start the sleep timer (OFF timer) operation

Press

: Select 1, 3, 5 or 9 hrs for OFF timer operation.

SLEEP

MAINTENANCE

Firstly, turn off the circuit breaker.

Filter Reset (Some models only)

FILTER lamp lights on; the ﬁ lter must be cleaned.

To turn off the lamp, push the RESET button on the indoor unit or the FILTER

button on the remote control.

Indoor Unit and Remote Control

• Clean the indoor unit and the remote control with a wet cloth when needed.

• No benzine, thinner, polishing powder or chemically-treated duster.

Cleaning the air ionizer (Once every six months) (RAS-10, 13, 16SKVR-E Only)

1. Turn off air conditioner using remote control and power supply.

2. Fully open the vertical air ﬂ ow louvers by hand.

3. Use a toothbrush to rub the ends of metal pin three or four times.

Note: Do not use cotton swabs or other objects with ﬂ uff.

Setting the OFF Timer

OFF

Press

: Set the desired OFF timer.

Press

: Set the timer.

SET

Press

: Cancel the timer.

CLR

SET

Press

SET

Press

button during the ( or )

mark ﬂ ashing.

Cleaning the plasma air puriﬁ er unit (About 1000 hours performed)

(RAS-10, 13, 16SKVR-E Only)

1. Turn off air conditioner using remote control and power supply.

2. Take out the air inlet grille (See detail in installation manual).

3. Take out the plasma air puriﬁ er by grasp the handle, and the pull it out.

4. Soak in hot water at 40

C to 50

down, left, right and rub surface gently with a sponge.

5. Allow to dry thoroughly in the shade.

6. Attach the plasma air puriﬁ er by grasp the handle

and insert into the right and left guide rails.

7. Press both ends of the plasma air puriﬁ er

until the protrusions on both sides of the

plasma air puriﬁ er are completely inserted.

8. Attach the air ﬁ lter, and then close the air inlet grille.

SELF CLEANING OPERATION (COOL AND DRY OPERATION ONLY)

To protect bad smell caused by the humidity in the indoor unit.

1. If the

button is pressed once during "Cool" or "Dry" mode, the fan will continue

to run for other 20 minutes, then it will turn off automatically. This will reduce the

moisture in the indoor unit.

2. To stop the unit immediately, press the

Note:

• SELF CLEANING operation is default setting from factory.

• To cancel this function, press and hold the reset button on the indoor unit for 20 seconds.

The SELF CLEANING operation will be cancelled. (5 beep sound but OPERATION

lamp does not blink)

• Do the same to set this function again. (5 beep sound and OPERATION lamp

blink 5 time/sec for 5 seconds)

• AUTO RESTART operation will be cancelled by setting or cancellation of SELF

CLEANING operation. Set it again if necessary.

OPERATION AND PERFORMANCE

1. Three-minute protection feature: To prevent the unit from being activated for 3

minutes when suddenly restarted or switched to ON.

2. Preheating operation: Warm up the unit for 5 minutes before the heating operation starts.

3. Warm air control: When the room temperature reaches the set temperature,

the fan speed is automatically reduced and the outdoor unit will stop.

4. Automatic defrosting: Fans will stop during defrost operation.

5. Heating capacity: Heat is absorbed from outdoors and released into the room.

When the outdoor temperature is too low, use another recommended heating

apparatus in combination with the air conditioner.

6. Consideration for accumulated snow: Select the position for outdoor unit where it will

not be subjected to snow drifts, accumulation of leaves or other seasonal debris.

7. Some minor cracking sound may occur when unit operating. This is normal

because the cracking sound may be caused by expansion/contraction of plastic.

Note: Item 2 to 6 for Heating model

Air conditioner operating conditions

Outdoor Temperature

Temp.

10, 13, 16SKVR-E

Operation

13, 16SKV-E

Heating

–15°C ~ 24°C

Cooling

–10°C ~ 46°C

Dry

–10°C ~ 46°C

Temp.

Outdoor Temperature

M10, 13, 16SK(C)V-E

Operation

Heating

Cooling

Dry

TROUBLESHOOTING (CHECK POINT)

The unit does not operate.

• The power main switch is turned off.

• The circuit breaker is activated to

cut off the power supply.

• Stoppage of electric current

• ON timer is set.

REMOTE CONTROL A-B SELECTION

To separate using of remote control for each indoor unit in case of 2 air conditioner

are installed nearly.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.

2. Point the remote control at the indoor unit.

3. Push and hold

button on the Remote Control by the tip of the pencil. "00" will

CHK ●

be shown on the display.

MODE

4. Press

during pushing

will disappear and the air conditioner will turn OFF. The Remote Control B is

memorized.

Note: 1. Repeat above step to reset Remote Control to be A.

2. Remote Control A has not "A" display.

3. Default setting of Remote Control from factory is A.

C for about 10 to 15 minutes and rub up,

3 times within 30 seconds.

Room

Temperature

10SKV-E

–10°C ~ 24°C

Less than 28°C

15°C ~ 43°C

21°C ~ 32°C

15°C ~ 43°C

17°C ~ 32°C

Room

Temperature

–15°C ~ 24°C

Less than 28°C

0°C ~ 43°C

21°C ~ 32°C

0°C ~ 43°C

21°C ~ 32°C

Cooling or Heating is abnormally low.

• The ﬁ lters are blocked with dust.

• The temperature has been set improperly.

• The windows or doors are opened.

• The air inlet or outlet of the outdoor

unit is blocked.

• The fan speed is too low.

• The operation mode is FAN or DRY.

. "B" will show on the display and "00"

CHK ●