Philips 3 DISC SHELF STSYEM W60 FWC3C37 사용자 설명서 - 페이지 15

{카테고리_이름} Philips 3 DISC SHELF STSYEM W60 FWC3C37에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Philips 3 DISC SHELF STSYEM W60 FWC3C37 28 페이지. Philips mini hi-fi systems brochure

페이지 인쇄

• If you press DISC CHANGE again

during playback, the CD will stop

playing.

™ The CD carousel tray will rotate

until the inner tray is rotated out

and is ready for changing.

3 Press OPEN•CLOSE to close the

CD carousel tray.

Selecting a desired track

Selecting a desired track when

playback is stopped

1 Press í or ë until the desired

track appears on the display.

2 PressÉ to start playback.

™ The selected track number and

elapsed playing time appear on

the display.

Selecting a desired track during

playback

• Press í or ë until the desired

track appears on the display.

™ The selected track number and

elapsed playing time appear on

the display.

• If you press í once it will skip to

the beginning of the current track

and play the track again.

Note:

– Pressing í during shuffling can only

skip to the beginning of the current

track.

pg 01-28/C3-35-30/37-Eng 1

Searching for a particular

passage during playback

• Press and hold à or á until the

desired passage is located.

™ The volume will be reduced.

• Play returns to normal when à or

á is released.

Programming Tracks

Programming tracks of a loaded CD is

possible when playback is stopped. The

display will indicate the total tracks

stored in the program. Up to 40 tracks

can be stored in the memory in any

order. When 40 tracks are stored and

you attempt to store another track, the

display will show "PROGRAM FULL".

1 Load the desired discs in the disc

trays.

2 Press PROGRAM to start

programming.

™ The PROG flag starts flashing.

™ It will cancel any previously

selected repeat mode.

3 Press the CD (CD 1•2•3) or DISC

1/2/3 button to select the disc.

4 Pressí or ë to select the desired

track.

5 Press PROGRAM to store the

track.

• Repeat steps 3 to 5 to store other

discs and tracks.

6 Press Ç once to end programming.

™ The total number of tracks

programmed and total playing

time appear on the display.

Notes:

– If the total playing time is more than

"99:59" or if one of the programmed

tracks has a number greater than 30,

then "--:--" appears on the display

instead of the total playing time.

– If the system is reading the discs,

programming is not possible,

"READING" will be displayed and

followed by "DISC X". "X" is the

current read disc number.

– During programming, if no button is

pressed within 20 seconds, the system

will exit program mode automatically.

Reviewing the program

Reviewing of the program is possible

only when playback is stopped.

• Pressí or ë repeatedly to review

the programmed tracks.

• Press Ç to exit review mode.

Playing the program

1 Press É to start program playback.

™ "PLAY PROGRAM" will be

displayed.

™ The track number and elapsed

playing time of the current track

will appear on the display.

12/14/99, 9:48 AM

• If you press REPEAT during

program playback, the current track

or all programmed tracks will be

played repeatedly.

™ "TRACK" or "PROGRAM" will be

displayed.

™ The REP and PROG flags appear

on the display.

2 Press Ç to stop program playback.

Notes:

– If you press any of the CD DIRECT

PLAY buttons, the system will play the

selected disc or track and the stored

program will be ignored temporarily.

The PROG display also will disappear

temporarily from the display. It will

reappear when playback of the

selected disc ends.

– REPEAT DISC mode will be cancelled

when program playback begins.

Erasing the program

(when

playback is stopped)

• Press Ç.

™ "PROGRAM CLEARED" will be

displayed.

Note:

– The program will be erased when the

system is disconnected from the power

supply or when the CD carousel tray is

opened.

3139 116 19372 (ENG)