Philips AZ-2040 사용자 설명서 - 페이지 8

{카테고리_이름} Philips AZ-2040에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Philips AZ-2040 9 페이지. Cd soundmachine
Philips AZ-2040에 대해서도 마찬가지입니다: 사용자 설명서 (15 페이지), 사용자 설명서 (12 페이지), 매뉴얼 (8 페이지), 서비스 매뉴얼 (34 페이지), 매뉴얼 (10 페이지), (스웨덴어) Snabbmanual (8 페이지)

페이지 인쇄

DIGITAL TUNER

3 Press and hold ∞ or § until the frequency in the

display starts running.

™ The radio automatically tunes to a station of

sufficient reception. Display shows

during automatic tuning.

™ If a FM station is received in stereo,

shown.

4 Repeat steps 2-3 if necessary until you find the

desired station.

• To tune to a weak station, press ∞ or § briefly

and repeatedly until you have found optimal

reception.

To improve radio reception:

• For FM, extend, incline and turn the telescopic

aerial. Reduce its length if the signal is too strong.

• For MW (AM), the set uses a built-in aerial. Direct

this aerial by turning the whole set.

Programming radio stations

You can store up to a total of 30 radio stations in the

memory, manually or automatically (Autostore).

Manual programming

1 Tune to your desired station (see Tuning to radio

stations).

2 Press PROG to activate programming.

3 Press PRESET DOWN/ UP once or more to select

a preset number.

4 Press PROG to confirm.

5 Repeat steps 1-4 to store other stations.

Note: You can erase a preset station by storing

another frequency in its place.

Autostore

Autostore automatically starts programming radio

stations from preset 1. Available stations are

programmed in order of waveband reception strength:

FM, followed by MW (AM). Any previous presets e.g.

manually programmed will be erased.

• Press PROG for 4 seconds or more to activate

autostore programming.

™ The display shows

, program blinks,

AUTO

followed by the radio station details when

stored. (See 5)

After all stations are stored, the first autostore preset

station will then automatically play.

To listen to a preset or autostore station

Press the PRESET (up or down) buttons once or more

until the desired preset station is displayed.

Changing tuning grid (some versions only)

In North and South America the frequency step

between adjacent channels in the AM and FM band

are 10 KHz and 100 KHz respectively. In the rest of the

world this step is 9 KHz and 50 KHz. Usually the

frequency step has been preset in the factory for your

area.

1 Check that the set is completely switched off.

2 To select 9KHz: Simultaneously, press MODE and

PRESET DOWN on the set.

3 Switch the set on to TUNER and then release the

controls.

• To select 10KHz: Repeat steps 1-3 but in step 2,

simultaneously, press MODE and PRESET UP on

the set.

™ When you tune to radio stations, the display

shows tuning in either steps of 9 kHz or 10 kHz.

™ All preset and autostore stations will be

affected and you may need to reprogramme

stations.

CD PLAYER

Playing a CD

This CD player plays Audio Discs including

CD-Recordables and CD-Rewritables.

1 Press y to on, then SOURCE to select

™

if no CD is inserted.

2 Insert a CD with the printed side facing up and

close the CD door.

™ Display: total number of tracks and playing time.

™

is shown if you have inserted a

non-finalized CD-R(W).

3 Press 2; to start playback.

™

if your CD contains non-audio

files

4 To pause playback press 2;. Press 2; again to

resume play.

5 To stop CD playback, press 9.

Note: CD play will also stop when:

– the CD door is opened

– the CD has reached the end

– you select tape or tuner source.

Selecting a different track

• Press ∞ or § on the set, once or repeatedly to

select.

• In the pause/stop position, press 2; to start

playback.

Finding a passage within a track

1 Press and hold ∞ or §.

™ The CD is played at high speed and low volume.

2 When you recognize the passage you want, release

∞ or § to resume normal playback.

Note: During a CD program or if shuffle/ repeat

active, searching is only possible within a track.

Different play modes: SHUFFLE and REPEAT

You can select and change the various play modes

before or during playback, and combine the modes

with PROGRAM.

shuffle – tracks of the entire CD/ program are

played in random order

shuffle and repeat all – to repeat the entire CD/

program continuously in random order

repeat all – repeats the entire CD/ program

repeat (and shuffle repeat) – plays the current

(random) track continuously

1 To select play mode, press MODE once or more.

2 Press 2; to start playback if in the stop position.

3 To select normal playback, press MODE repeatedly

until the various modes are no longer displayed.

– You can also press 9 to cancel your play mode.

Programming track numbers

In the stop position, select and store your CD tracks in

the desired sequence. Up to 20 tracks can be stored in

the memory.

1 Press ∞ or § on the set to select your desired

track number.

CASSETTE RECORDER

2 Press PROG.

™ If you attempt to program without first selecting

a track number,

is shown.

3 Repeat steps 1-2 to select and store all desired

tracks.

™ Display:

if you try to program more than

20 tracks.

Reviewing the program

In the stop position, press and hold PROG until the

display shows all your stored track numbers in

sequence.

Erasing a program

You can erase the program by:

• pressing 9 twice

™

is displayed briefly and

disappears.

• selecting

source.

TAPE

TUNER

CASSETTE RECORDER

Cassette playback

1 Press y to on, then SOURCE to select

TAPE

™ Display: shows

throughout tape

operation.

2 Insert a cassette and close the door.

3 Press PLAY 2 to start playback.

4 To pause, press PAUSE ;. Press again to resume.

5 Press SEARCH 5 or 6 to fast wind the tape.

6 To stop the tape, press STOP 9.

• The keys are automatically released at the end of a

tape, except if PAUSE ; has been activated.

GENERAL INFORMATION ON RECORDING

• Recording is permissible insofar as copyright or.

other rights of third parties are not infringed.

• For recording, use only NORMAL type cassettes

(IEC type I) on which the tabs have not yet been

broken. This deck is not suited for recording on

CHROME (IEC II) or METAL (IEC IV) type cassettes.

• The best recording level is set automatically.

Altering the VOLUME, DBB or BASS, MID &

HIGH controls will not affect the recording.

• To protect a tape from accidental erasure, break

out the tabs. If you wish to record again, cover the

tabs with a piece of adhesive tape.