Philips AZ1836 사용자 설명서 - 페이지 7
{카테고리_이름} Philips AZ1836에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Philips AZ1836 8 페이지. Mp3 cd soundmachine
Philips AZ1836에 대해서도 마찬가지입니다: 사양 (2 페이지), 사양 (2 페이지), 사양 (2 페이지), 빠른 사용 설명서 (1 페이지), 사용자 설명서 (16 페이지), 빠른 사용 설명서 (2 페이지), 빠른 사용 설명서 (1 페이지), 사용자 설명서 (9 페이지), 서비스 매뉴얼 (19 페이지)
페이지 인쇄
Safety & Maintenance (See !)
Safety information
•
Place the set on a hard, flat and stable surface
so that the system does not tilt.
•
Do not expose the set, batteries, CDs to
humidity, rain, sand or excessive heat caused
by heating equipment or direct sunlight.
•
The apparatus shall not be exposed to
dripping or splashing.
•
Adequate ventilation with a minimum gap of
15 cm between the ventilation holes and sur-
rounding surfaces is necessary to prevent
heat build-up.
•
The ventilation should not be impeded by
covering the ventilation openings with items,
such as newspapers, table-cloths, curtains, etc..
•
No objects filled with liquids, such as vases,
shall be placed on the apparatus.
•
No naked flame sources, such as lighted can-
dles, should be placed on the apparatus.
•
The mechanical parts of the set contain
self-lubricating bearings and must not be oiled
or lubricated.
•
To clean the set, use a dry cloth. Do not use
any cleaning agents containing alcohol,
ammonia, benzene or abrasives as these may
harm the housing.
Environmental information
All unnecessary packaging material has been omitted.The packaging can be easily separated
into three materials: cardboard, polystyrene and plastic.
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packaging, dead batteries and old equipment.
CD player and CD handling
•
If the CD player cannot read CDs correctly,
use a cleaning CD to clean the lens before
taking the set to repair.
•
The lens of the CD player should never be
touched!
•
Sudden changes in the surrounding
temperature can cause condensation on the
lens of your CD player. Playing a CD is then
not possible. Do not attempt to clean the
lens but leave the set in a warm environment
until the moisture evaporates.
•
Always close the CD door to avoid dust on
the lens.
•
To clean the CD, wipe in a straight line from
the center towards the edge using a soft,
lint-free cloth. Do not use cleaning agents as
they may damage the disc.
•
Never write on a CD or attach any stickers
to it.
Troubleshooting
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
WARNING:
Do not open the set as there is a risk of electric shock. Under no cir-
cumstances should you try to repair the set yourself, as this will inval-
idate the guarantee.
No sound/ power
– Volume not adjusted
• Adjust the VOLUME
– Power cord not securely connected
• Connect the AC power cord properly
– Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
– Disc contains non-audio files
• Insert a suitable disc or press ∞ or § once or
more skip to an audio track, instead of the data
files.
Display does not function properly/No
reaction to operation of any of the
controls
– Electrostatic discharge
• Switch off and unplug the set. Reconnect after a
few seconds.
no indication
– It is set in the USB mode.
• Press CD/USB to select CD mode.
– No disc inserted
• Insert a suitable disc
– Disc badly scratched or dirty
• Replace/clean CD (See Maintenance)
– CD-R(W) is blank or the disc is not finalized.
• Use a finalized CD-R(W)
– Laser lens steam up
• Wait until lens has cleared.
Note:
Make sure the CD is not encoded with
Copyright protection technologies, as some
do not conform to the Compact
Disc standard.
The disc skips tracks
– Disc damaged or dirty
• Replace or clean disc
– Shuffle or program is active
• Switch off shuffle/program
Sound skips during MP3 playback
– MP3 file made at compression level exceeding
320kbps
• Use a lower compression level to record CD
tracks into MP3 format
– Disc damaged or dirty
• Replace or clean disc.
Note:
DRM-protected WMA disc is not supported.
The USB device doesn't play on my
AZ1836
– It is not set in the USB mode.
• Press CD/USB to select USB mode.
– The device is not securely connected to AZ1836's
USB port.
• Re-connect the device, and make sure that the
device is powered on.
– The device is not supported by AZ1836, or the audio
file format stored on the device is not supported by
AZ1836.
• Use a compatible device/ playable audio file
format.
The disc file cannot be recorded to the
USB device
– You stop recording when the MP3 or WMA file you
want to record is still playing.
• Select record-one mode to record, or stop
recording only when the playback of MP3 or
WMA file is wholly completed.
– The memory of the USB device runs out.
• Delete some unwanted files on the USB device to
free some memory, or use another USB device of
sufficient free memory to record.
– The name of a MP3 or WMA file on the disc is
identical to the one of a file on the USB device.
• Change to a different name for the file on the
USB device.