Toshiba TLP-710U 서비스 매뉴얼 - 페이지 10
{카테고리_이름} Toshiba TLP-710U에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Toshiba TLP-710U 30 페이지. 3 lcd data projector
Toshiba TLP-710U에 대해서도 마찬가지입니다: 소유자 매뉴얼 (48 페이지), 기술 교육 매뉴얼 (31 페이지)
페이지 인쇄
4-1. LCD Drive Adjustment (A) (In case of "TA" type optical engine)
Adjust Items
Input Signal
1. Input level check
1-1. Input level check
16-stairstep
1-2. Input level
16-stairstep
adjustment of RGB
signals
1-3. Input level
Gray scale or
adjustment of
video signal
2. PSIG adjustment
2-1. SID level adjust-
ment
2-2. PRG level
adjustment
3. Gamma adjustment
3-1. Center voltage
16-stairstep
adjustment
3-2. Bias adjustment
16-stairstep
3-3. Black gamma
16-stairstep
adjustment
Test
Equip-
Test Point
ment
Oscillo-
TP405 (R)
waveform
scope
TP505 (G)
TP605 (B)
Oscillo-
TP701 (R)
waveform
scope
TP702 (G)
TP703 (B)
Oscillo-
TP701
stairstep
scope
TP702
waveform
TP703
––––
Oscillo-
TP403
scope
(TP503) (G)
(TP603) (B)
––––
Oscillo-
TP403
scope
(TP503) (G)
(TP603) (B)
Oscillo-
TP402 (R)
waveform
scope
TP502 (G)
TP602 (B)
Oscillo-
TP402 (R)
waveform
scope
TP502 (G)
TP602 (B)
Oscillo-
TP402 (R)
waveform
scope
TP502 (G)
TP602 (B)
Table 1-4-1
Adjust Key
Adjust Value
• 0.86V ± 100 mV
between pedestal
and white level of
sixteenth stair-
step waveform
• 1.2V ± 20 mV
VGR
between pedestal
VGG
and white level of
VGB
sixteenth stair-
step waveform
• 1.2V ± 20 mV
VGR
between pedestal
VGG
and white level
VGB
(R)
• Adjust at R so that
WM0
amplitude of
waveform A in the
right obtains 3.8V
± 50 mV. Then
check at G and B.
(R)
• Adjust at R so that
WM1
amplitude of
waveform A in the
right obtains 9V ±
50 mV. Then
check at G and B.
• Adjust for A = B
WM7
as shown in
illustration right.
• Adjust the 16th
W03
stairstep wave-
W04
form for following
W05
values:
(R): 6.96 ± 20 mV
(G): 6.86 ± 20 mV
(B): 6.76 ± 20 mV
• Adjust the 2nd
W09
stairstep wave-
W0A
form for following
W0B
values:
(R): 4.34V ± 60 mV
(G): 4.10V ± 60 mV
(B): 4.04V ± 60 mV
1-8
Note
• Perform adjustment in
IN1
and
modes.
IN4
• Trigger the scope at TP901
(H period).
• Perform adjustment in
IN1
mode and RGB1 input.
• Trigger the scope at TP901
(H period).
• Perform adjustment in
IN4
mode and Video 2 input.
• Trigger the scope at TP901
(H period).
B
A
• Trigger the scope at TP901
(H period).
16th stairstep
• Trigger the scope at TP901
(H period).
2nd stairstep