Dimplex CKHA Series 설치 지침 - 페이지 2

{카테고리_이름} Dimplex CKHA Series에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Dimplex CKHA Series 2 페이지. Kickspace heater
Dimplex CKHA Series에 대해서도 마찬가지입니다: 기능 및 사양 (1 페이지), 소유자 매뉴얼 (3 페이지), 사용 설명서 (10 페이지)

페이지 인쇄
Dimplex CKHA Series 설치 지침
Soffit or Stair Riser Installation
Soffit or Stair Riser Installation
1. Cut opening as for kickspace installation (22 3/8" x
1. Cut opening as for kickspace installation (22 3/8" x
3 5/8"). Allow 3/4" clearance above cabinet doors.
3 5/8"). Allow 3/4" clearance above cabinet doors.
Add supports for unit (Fig.3).
Add supports for unit (Fig.3).
2. Proceed as for kickspace installation. After
2. Proceed as for kickspace installation. After
securing unit in opening, install combination of
securing unit in opening, install combination of
frame and grille (fig.1).
frame and grille (fig.1).
CAUTION - Disconnect main to de-energize receptacle
CAUTION - Disconnect main to de-energize receptacle
before servicing or for electrical inspection.
before servicing or for electrical inspection.
SERVICING - Remove grille and frame by removing
SERVICING - Remove grille and frame by removing
screws "A". Remove two screws "B", and slide out heating assembly. When re-assembling, reverse the
screws "A". Remove two screws "B", and slide out heating assembly. When re-assembling, reverse the
procedure above.
procedure above.
Cleaning
Cleaning
With grille in place - Use vacuum cleaner hose to suck out lint and dirt around grille. Reverse hose on vacuum to
With grille in place - Use vacuum cleaner hose to suck out lint and dirt around grille. Reverse hose on vacuum to
use as a blower to move dust out of enclosure. Reverse hose back to suck out dirt at front area of heater.
use as a blower to move dust out of enclosure. Reverse hose back to suck out dirt at front area of heater.
With grille removed - Remove two screws "B" at bottom front of heating element assembly. Pull gently to remove
With grille removed - Remove two screws "B" at bottom front of heating element assembly. Pull gently to remove
it from enclosure. Swing assembly out. Vacuum inside of enclosure and around heating element assembly.
it from enclosure. Swing assembly out. Vacuum inside of enclosure and around heating element assembly.
Reverse procedure above to re-assemble unit.
Reverse procedure above to re-assemble unit.
Thermostat Adjustment (CKHATD13 / CKHATD23)
Thermostat Adjustment (CKHA20D31T)
Adjust thermostat with screwdriver.
Adjust thermostat with screwdriver.
CATALOG NO.
MOTOR
CKHA20D31
CKHA20D31W
FACTORY CONNECTION
RKHA20D31W
2000280400RP
208/240 VOLT 675/900 WATTS
3.2 A / 3.7A
FACTORY CONNECTION
208/240 VOLT 675/900 WATTS
3
1
5
3.2 A / 3.7A
M
FAN
2
4
6
FAN
M
IMPORTANT: RETIGHTEN ALL LEADS WITH CABLE CLAMP
AFTER RECONNECTING UNINSULATED ENDS OF
UNUSED LEADS WITH WIRE NUTS.
SAFETY SWITCH
IMPORTANT: RETIGHTEN ALL LEADS WITH CABLE CLAMP
NOTE: If installing unit with factory thermostat, see
AFTER RECONNECTING UNINSULATED ENDS OF
supplemental wiring diagram, fig. 4a.
UNUSED LEADS WITH WIRE NUTS
7200960100R04
NOTE: If installing unit with factory thermostat, see
supplemental wiring diagram, Fig. 4a.
FAN BLADE
FIELD CONNECTION
5300210100RP
208/240 VOLT 1350/1800 WATTS
6.5 A / 7.5 A
FACTORY CONNECTION
208/240 VOLT 1350/1800 WATTS
7
6.5 A / 7.5 A
FAN
8
SAFETY SWITCH
FAN
M
CEILING
GRILLE
HEATER
CABINET DOOR
REPLACEMENT PART
ELEMENT
2203260100RP
1
3
5
7
M
2
4
6
8
SAFETY SWITCH
SAFETY SWITCH
PARTITION OR
ADDED SUPPORT
CUT OUT
CUT OUT
(MANUAL)
(AUTOMATIC)
FIELD CONNECTION
03005035RP
211A619RP
120 VOLT
FACTORY CONNECTION
120 VOLT
1
3
M
FAN
2
4
6
M
FAN
RATING
450W/ 3.75A
900W/ 7.5A
1350W/ 11.2A
1800W/ 15A
RATING
450W/ 3.75A
900W/ 7.5A
1350W/ 11.2A
1800W/ 15A
3/4"
MIN
Fig. 3
Fig 3.
GRILLE KIT
CKHABG
Fig. 4
CKHAWG
CKHAWG
Fig. 4
5
7
8
SAFETY SWITCH
CONNECT
7-8 (AS SHOWN)
7-8, 1-2
7-8, 1-2, 3-4
7-8, 1-2, 3-4, 5-6
SAFETY SWITCH
CONNECT
Fig. 4a
7-8 (AS SHOWN)
7-8, 1-2
THERMOSTAT
7-8, 1-2, 3-4
7-8, 1-2, 3-4, 5-6
Fig. 4a
THERMOSTAT