DimSport Rapid Bike 빠른 시작 매뉴얼
{카테고리_이름} DimSport Rapid Bike에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DimSport Rapid Bike 2 페이지.
페이지 인쇄
1.
Update the EVO/RACING module firmware with Rapid Bike software version 2.0.6.8 or further
2.
Fasten the device, using the supplied Velcro, in a position easy to look at and reach (see picture)
3.
Route YOUTUNE wiring harness up to the Rapid Bike module and fasten it to the OEM harness using cable ties
4.
Connect the three connectors of YOUTUNE harness to the Rapid Bike main wiring harness
5.
Turn ignition on. Device must light up all LEDs and the display; then it should set to RPM position showing 0 rpm
PLEASE PAY ATTENTION TO THE FOLLOWING:
- DO NOT TAKE AWAY YOUR ATTENTION FROM DRIVING WHILE OPERATING WITH THIS DEVICE
- USE ONLY WITHIN ENCLOSED RACING TRACKS, NOT INTENDED FOR STREET AND PUBLIC ROADS USE
- YOUTUNE SPECIFIC FUNCTIONS ARE LISTED FOR EACH SINGLE BIKE MODEL ON RAPID BIKE APPLICATION LIST AVAILABLE ON-LINE
Ten LEDs on a curved line for
analog representation of specific
values being measure:
blue = low - red = high
Button MODE selects
a specific feature and
saves new settings in
Rapid Bike module's
memory
Six LEDs indicating the selected feature:
TC => Traction Control
EB => Engine Braking
QS => Electronic Quick Shifter
AFR => Air Fuel Ratio
LC => Launch Control
RPM => Revolutions per Minute
+
RPM
RPM: showing the information listed above; pushing (-) button for 2 seconds it enables a RPM/Speed
Control function to maintain engine rpm at constant level, therefore cruising at constant speed.
(*) Bike models equipped with ride-by-wire system CAN NOT disable this RPM/Speed Control function
by opening at full gas; be sure to use the other two systems as described above
MODE
AFR
O2 Target
_
O2 sensor heating
O O2 sensor operating
OO O2 sensor operating / Rapid Bike
is modulating
AFR: Changing target value of auto-adaptive feature in order to modify fuel adjustments performed automatically
by EVO and RACING modules and obtain a richer (+ means more gasoline) or leaner (- means less gasoline ) fuel mixture.
Default value is 0 (no variations of auto-adaptive feature's target), and it can be modified of +/- 2 points. An additional push after -2 points value stops
auto-adaptive feature from operating and display shows "OFF"; keep in mind latest correction values will continue to be applied.
YOUTUNE operates directly on the Air/Ruel Ratio with modifications up to +/- 10 points (1 point = 0,1 AFR) ONLY when it is installed one or more My
Tuning Bike unit. An additional push after -9 point value stops this function, while latest correction values continue to be applied.
Quick start guide
TPS
+
RPM
̶
2sec.
+
AFR
̶
Button (-)
decreases the
value displayed
and activates
RPM/Speed
control
AFR
+
RPM
+
100rpm
RPM limiter
100rpm
-
AFR
+
oo
1
AFR
̶
oo
-1
full version can be downloaded
from
www.rapidbike.com
Button (+) increases the value
displayed. Pressed together
with button (-) allows
modifying the brightness
Alphanumeric display shows the
value of the selected feature
TECHNICAL TERMS
TPS = Throttle Position Sensor
O2 = Oxygen / Lambda sensor
Ride-by-wire = Electronic
throttle
RPM
+
Gear TPS
MODE
̶ 2sec.
Full gas*
AFR
oo
2
AFR
̶
oo
-2
oo
AFR
O2 TPS
STOP
RPM
limiter
AFR
OFF