Pioneer AVX-P8DVD 설치 매뉴얼 - 페이지 4

{카테고리_이름} Pioneer AVX-P8DVD에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer AVX-P8DVD 9 페이지. Owner's manual
Pioneer AVX-P8DVD에 대해서도 마찬가지입니다: 소유자 매뉴얼 (34 페이지), 운영 매뉴얼 (4 페이지)

페이지 인쇄

Installation

Note:

Installing the remote control unit

• Before finally installing the unit, connect the

wiring temporarily, making sure it is all connected

When not using the remote control unit,

up properly, and the unit and the system work

secure it with velcro tape to prevent it

properly.

from moving.

• Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts

• Thoroughly wipe off the surface

can cause malfunctions.

before affixing the velcro tape.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifications

Remote control

of the vehicle.

• Install the unit where it does not get in the driver's

unit

way and cannot injure the passenger if there is a

Velcro tape (small)

sudden stop, like an emergency stop.

(hard)

• Do not install the display where it may (i) obstruct

Velcro tape (small)

the driver's vision, (ii) impair the performance of

(soft)

any of the vehicle's operating systems or safety

features, including air bags, hazard lamp buttons or

(iii) impair the driver's ability to safely operate the

vehicle.

• The semiconductor laser will be damaged if it

overheats, so don't install the unit anywhere hot

— for instance, near a heater outlet.

• If installation angle exceeds 30° from horizontal,

the unit might not give its optimum performance.

(Fig. 8)

30°

Fig. 8

• The cords must not cover up the area shown in the

figure below. This is necessary to allow the ampli-

fires to radiate freely. (Fig. 9)

Do not close this area.

Fig. 9

DIN Front/Rear-mount

This unit can be properly installed

either from "Front" (conventional DIN

Front-mount) or "Rear" (DIN Rear-

mount installation, utilizing threaded

screw holes at the sides of unit chassis).

For details, refer to the following illus-

trated installation methods.

Before installing the unit

Flush surface screw (5 × 6 mm)

• Remove the frame and the hold-

er. (Fig. 11)

Pull out to remove the frame and then

loosen the screws (2 × 3 mm) to

2. Install the unit into the dash-

remove the holder. (When reattaching

board. (Fig. 13)

the frame, point the side with a groove

After inserting the holder into the dash-

downwards and attach it.)

Fig. 10

board, then select the appropriate tabs

according to the thickness of the dash-

board material and bend them.

(Install as firmly as possible using the

top and bottom tabs. To secure, bend

the tabs 90 degrees.)

Holder

Dashboard

Screw (2 × 3 mm)

Frame

Fig. 11

DIN Front-mount

Holder

Installation with the rubber bush

1. Decide the position of the side

brackets. (Fig. 12)

When installing in a shallow space,

change the position of side brackets. In

this case, stick conceal tape on parts

• After installing the unit into the dash-

that protrude from the dashboard.

board, reattach the frame.

DIN Rear-mount

Installation using the screw holes on

the side of the unit

• Fastening the unit to the factory

radio mounting bracket. (Fig. 14)

Conceal tape

(Fig. 15) (Fig. 16)

Select a position where the screw holes

Side bracket

of the bracket and the screw holes of

this product become aligned (are fitted),

and tighten the screws at 2 places on

Fig. 12

each side. Use any of binding screws (4

× 3 mm), binding screws (5 × 6 mm) or

flush surface screws (5 × 6 mm),

depending on the shape of the screw

holes in the bracket.

*1 Use binding screws (4 × 3 mm) only.

* 1

182

Rubber bush

• When installing in a shallow space,

Screw

use the following screw holes. In this

case, stick conceal tape on parts that

protrude from the dashboard.

Conceal tape

Side bracket

* 1

Screw (2 × 3 mm)

* 1

Fig. 13

Switching the operation mode

Screw

This unit features two operation modes:

the IP-BUS mode (S) and the ADD-ON

mode (M). Switch the mode according

to the combined components.

• IP-BUS mode (S) – Using with a

Pioneer head unit featuring an IP-

BUS input or multi-channel proces-

Dashboard or

sor control unit

Console

• ADD-ON mode (M) – Using with a

Factory radio mounting

car stereo featuring RCA audio

bracket

inputs or FM reception capability

Fig. 16

• Use a thin standard tip screw-

driver to switch the operation

mode switch on the back of this

Fixing the front panel

unit. (Fig. 18)

If you do not operate the removing and

attaching the front panel function, use

the supplied fixing screws to fix the

front panel to this unit.

• Fix the front panel to the unit

using fixing screws. (Fig. 17)

• After switching, reset the micro-

processor.

Fig. 14

Fixing screws

Fig. 17

Fig. 15

Fig. 18