Pioneer DEH-1300 설치 매뉴얼

{카테고리_이름} Pioneer DEH-1300에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-1300 6 페이지. High power cd player with fm/am tuner
Pioneer DEH-1300에 대해서도 마찬가지입니다: 운영 매뉴얼 (30 페이지)

페이지 인쇄

1. DIN Front/Rear-Mount

DEH-2300

DEH-1300

DEH-23

DEH-12

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit

est conforme à CEMA.

Los colores de los cables este producto se conforman

con el código de colores CEMA.

Printed in

Imprimé

<CRD3280-B/JS> UC

Connecting the Units

Note:

•

This unit is for vehicles with a 12-volt battery

•

When this product's source is switched ON, a

and negative grounding. Before installing it in a

control signal is output through the blue/white

recreational vehicle, truck, or bus, check the bat-

lead. Connect to an external power amp's system

tery voltage.

remote control or the car's Auto-antenna relay

•

To avoid shorts in the electrical system, be sure

control terminal (max. 300 mA 12 V DC). If the

to disconnect the ≠ battery cable before begin-

car features a glass antenna, connect to the anten-

ning installation.

na booster power supply terminal.

•

Refer to the owner's manual for details on con-

•

When an external power amp is being used with

necting the power amp and other units, then

this system, be sure not to connect the blue/white

make connections correctly.

lead to the amp's power terminal. Likewise, do

not connect the blue/white lead to the power ter-

•

Secure the wiring with cable clamps or adhesive

minal of the auto-antenna. Such connection could

tape. To protect the wiring, wrap adhesive tape

cause excessive current drain and malfunction.

around them where they lie against metal parts.

•

To avoid short-circuiting, cover the disconnected

•

Route and secure all wiring so it cannot touch

lead with insulating tape. Especially, insulate the

any moving parts, such as the gear shift, hand-

unused speaker leads without fail. There is a pos-

brake and seat rails. Do not route wiring in

sibility of short-circuiting if the leads are not

places that get hot, such as near the heater outlet.

insulated.

If the insulation of the wiring melts or gets torn,

•

If this unit is installed in a vehicle that does not

there is a danger of the wiring short-circuiting to

have an ACC (accessory) position on the ignition

the vehicle body.

switch, the red lead of the unit should be con-

•

Don't pass the yellow lead through a hole into

nected to a terminal coupled with ignition switch

the engine compartment to connect to the battery.

ON/OFF operations. If this is not done, the vehi-

This will damage the lead insulation and cause a

cle battery may be drained when you are away

very dangerous short.

from the vehicle for several hours. (Fig.1)

•

Do not shorten any leads. If you do, the protec-

tion circuit may fail to work when it should.

•

Never feed power to other equipment by cutting

the insulation of the power supply lead of the

unit and tapping into the lead. The current capac-

ity of the lead will be exceeded, causing over-

heating.

•

When replacing fuse, be sure to use only fuse of

the rating prescribed on this unit.

•

Since a unique BPTL circuit is employed, never

ACC position

No ACC position

wire so the speaker leads are directly grounded or

the left and right ≠ speaker leads are common.

•

The black lead is ground. Please ground this lead

•

Speakers connected to this unit must be high-

separately from the ground of high-current prod-

power types with minimum rating of 45 W

(50 W)* and impedance of 4 to 8 ohms.

ucts such as power amps.

Connecting speakers with output and/or imped-

If you ground the products together and the

ground becomes detached, there is a risk of dam-

ance values other than those noted here may

age to the products or fire.

result in the speakers catching fire, emitting

smoke, or becoming damaged.

* DEH-2300 and DEH-23

•

Cords for this product and those for other prod-

ucts may be different colors even if they have the

same function. When connecting this product to

another product, refer to the supplied Installation

manuals of both products and connect cords that

have the same function.

Connection Diagram

This product

Rear output

Antenna jack

Yellow

To terminal always supplied

with power regardless of

ignition switch position.

Red

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

Black (ground)

To vehicle (metal) body.

Fig. 1

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

Perform these connections when using a

different amp (sold separately).

Connecting cords

with RCA pin plugs

(sold separately).

Fuse

Blue/white

To system control terminal of the power amp or Auto-antenna

relay control terminal (max. 300 mA 12 V DC).

System remote control

White

Gray

Front speaker

≠

White/black

Gray/black

Left

Green

Violet

Rear speaker

≠

Green/black

Violet/black

Rear speaker

≠

Power amp

(sold separately)

Front speaker

≠

Right

Rear speaker

≠

Rear speaker

≠

Fig. 2