Pioneer DEH-140UB 소유자 매뉴얼 - 페이지 8

{카테고리_이름} Pioneer DEH-140UB에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-140UB 16 페이지. Cd rds receiver
Pioneer DEH-140UB에 대해서도 마찬가지입니다: 소유자 매뉴얼 (45 페이지), 서비스 매뉴얼 (13 페이지)

페이지 인쇄

Operating this unit

DEMO (demo display setting)

1 Press M.C. to turn the demo display on or off.

! If PW SAVE is on, DEMO cannot be selected.

SCROLL (scroll mode setting)

When ever scroll is set to ON, recorded text infor-

mation scrolls continuously in the display. Set to

OFF if you prefer the information to scroll just

once.

1 Press M.C. to turn the ever scroll on or off.

TITLE (multi-language)

This unit can display the text information of a com-

pressed audio file even if they are embedded in a

Western European or Russian language.

! If the embedded language and the selected

language setting are not the same, text infor-

mation may not display properly.

! Some characters may not be displayed prop-

erly.

1 Press M.C. to select the desired setting.

EUR (European)—RUS (Russian)

PW SAVE (power saving)

Only for DEH-142UB, DEH-140UB and DEH-

140UBB.

Switching this function on enables you to reduce

the consumption of battery power.

! Turning on the source is the only operation al-

lowed when this function is on.

1 Press M.C. to turn the power save on or off.

Using an AUX source

Insert the stereo mini plug into the AUX

input jack.

Press SRC/OFF to select AUX as the

source.

Note

AUX cannot be selected unless the auxiliary set-

ting is turned on. For more details, refer to AUX

(auxiliary input) on the previous page.

Turning the clock display on

or off

% Press

to turn the clock display on or

off.

# The clock display disappears temporarily when

you perform other operations, but the clock display

appears again after 25 seconds.

Sound muting

Only for DEH-142UB, DEH-140UB and DEH-

140UBB.

Sound is muted automatically when:

! A call is made or received using a cell phone

connected to this unit.

! Voice guidance is output from a connected

Pioneer navigation unit.

The sound is turned off, MUTE is displayed and

no audio adjustments, except volume control,

are possible. Operation returns to normal when

the phone connection or the voice guidance is

ended.

Autogood products «130»

Installation

Connections

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

ACC position

No ACC position

! Use of this unit in conditions other than the

following could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring

that comes into contact with metal parts to

protect the wiring.

— Place all cables away from moving parts,

such as the shift lever and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

— Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an ex-

ternal power amp or the vehicle's auto-anten-

na relay control terminal (max. 300 mA

12 V DC). If the vehicle is equipped with a

glass antenna, connect it to the antenna

booster power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal

of the auto antenna. Doing so may result in

battery drain or a malfunction.

! The black cable is ground. Ground cables for

this unit and other equipment (especially,

high-current products such as power amps)

must be wired separately. If they are not, an

accidental detachment may result in a fire or

malfunction.

This unit

DEH-142UB, DEH-140UB and DEH-140UBB

DEH-141UB

1 Power cord input

2 Rear output

Section