Pioneer DEH-2490UB 소유자 매뉴얼 - 페이지 8

{카테고리_이름} Pioneer DEH-2490UB에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-2490UB 21 페이지. Cd rds receiver

페이지 인쇄

Section

Operating this unit

REPEAT (repeat play)

1 Press M.C. to select a repeat play range.

For details, refer to Selecting a repeat play range

on the previous page.

SHUFFLE (shuffle)

1 Press M.C. to select your favorite setting.

! SNG – Play back songs in the selected list

in random order.

! ALB – Play back songs from a randomly se-

lected album in order.

! OFF – Cancel random play.

SHUFFLE ALL (shuffle all)

1 Press M.C. to turn shuffle all on.

To turn off, set SHUFFLE in the FUNCTION

menu to off.

LINK PLAY (link play)

1 Press M.C. to display the setting mode.

2 Turn M.C. to change the mode; press to select.

For details about the settings, refer to Playing

songs related to the currently playing song on

the previous page.

PAUSE (pause)

1 Press M.C. to pause or resume.

AUDIO BOOK (audiobook speed)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select your favorite setting.

! FASTER – Playback at a speed faster than

normal

! NORMAL – Playback at normal speed

! SLOWER – Playback at a speed slower

than normal

3 Press M.C. to confirm the selection.

S.RTRV (sound retriever)

Automatically enhances compressed audio and

restores rich sound.

1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on the previous page.

Audio adjustments

Press M.C. to display the main menu.

Turn M.C. to change the menu option

and press to select AUDIO.

Turn M.C. to select the audio function.

After selecting, perform the following proce-

dures to set the audio function.

FAD/BAL (fader/balance adjustment)

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between fader (front/rear)

and balance (left/right).

3 Turn M.C. to adjust speaker balance.

! When the rear output and RCA output setting

are SW, you cannot adjust front/rear speaker

balance. Refer to REAR-SP (rear output setting)

on the next page. Refer to PREOUT (preout set-

ting) on the next page.

PRESET EQ (equalizer recall)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the equalizer.

DYNAMIC—VOCAL—NATURAL—CUSTOM

—FLAT—POWERFUL

3 Press M.C. to confirm the selection.

! You can also switch the equalizer by pressing

repeatedly (DEH-2490UB).

TONE CTRL (equalizer adjustment)

Operating this unit

! Adjusted equalizer curve settings are stored in

CUSTOM.

1 Press M.C. to display the setting mode.

2 Press M.C. to select BASS (bass)/MID (mid)/

TREBLE (treble).

3 Turn M.C. to adjust the level.

Adjustment range: +6 to –6

LOUD (loudness)

Loudness compensates for deficiencies in the low-

frequency and high-frequency ranges at low vol-

ume.

1 Press M.C. to select the desired setting.

OFF (off)—LOW(low)—HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output

which can be turned on or off.

! This function is not available for DEH-2490UB.

1 Press M.C. to select the desired setting.

NOR (normal phase)—REV (reverse phase)—

OFF (subwoofer off)

SUB.W CTRL (subwoofer adjustment)

The cut-off frequency and output level can be ad-

justed when the subwoofer output is on.

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

! This function is not available for DEH-2490UB.

! When you select OFF in SUB.W, you cannot se-

lect this function. For details, refer to SUB.W

(subwoofer on/off setting) on this page.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the cut-off fre-

quency and output level of the subwoofer.

Cut-off frequency (Cut-off frequency display

flashes.)—Output level (Output level display

flashes.)

3 Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—

100HZ—125HZ

Output level: –24 to +6

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the

volume level of each source to prevent radical

changes in volume when switching between sour-

ces.

! Settings are based on the FM volume level,

which remains unchanged.

! The MW volume level can also be adjusted

with this function.

! When selecting FM as the source, you cannot

switch to SLA.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

3 Press M.C. to confirm the selection.

Initial settings

Press and hold SRC/OFF until the unit

turns off.

Press M.C. and hold until function name

appears in the display.

Turn M.C. to select the initial setting.

After selecting, perform the following proce-

dures to set the initial setting.

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode.

2 Press M.C. to select the segment of the clock

display you wish to set.

Hour—Minute

3 Turn M.C. to adjust the clock.

FM STEP (FM tuning step)