Pioneer DEH-7200SD 설치 매뉴얼 - 페이지 5

{카테고리_이름} Pioneer DEH-7200SD에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-7200SD 8 페이지. Cd rds receiver
Pioneer DEH-7200SD에 대해서도 마찬가지입니다: 운영 매뉴얼 (28 페이지), 빠른 시작 매뉴얼 (9 페이지)

페이지 인쇄

1. Connecting/Diagram

8. Notes

1. This product

• Change the initial setting of this unit (refer to the

operation manual). The subwoofer output of this unit is

monaural.

7. Antenna

• When using a subwoofer of 70 W (2 Ω), be sure to

jack

connect with Violet and Violet/black leads of this unit.

Do not connect anything with Green and Green/black

6. Fuse (10 A)

leads.

9. Note

Depending on the kind of vehicle,

the function of 2* and 4* may be

different. In this case, be sure to

connect 1* to 4* and 3* to 2*.

10. Connect leads of the

same color to each other.

11. Yellow (2*)

12. Yellow (1*)

Back-up (or

Connect to the constant

accessory)

12 V supply terminal.

13. Red (4*)

14. Red (3*)

Accessory

Connect to terminal controlled by

(or back-up)

ignition switch (12 V DC).

15. Orange/white

Connect to lighting switch terminal.

16. Black (chassis ground)

Connect to a clean, paint-free metal location.

17. ISO connector

18. Yellow/black

Note

If you use an equipment with Mute

In some vehicles, the ISO connector may be

function, wire this lead to the Audio Mute

lead on that equipment. If not, keep the

divided into two. In this case, be sure to

Audio Mute lead free of any connections.

connect to both connectors.

23. To rear output

2. Rear output

24. To front output

3. Front output

4. Subwoofer output

25. To subwoofer output

26. Power amp

5. Wired remote input

(sold separately)

Hard-wired remote

control adaptor can

be connected (sold

separately).

27. Connect with RCA cables

(sold separately)

28. System remote control

19. Blue/white

Connect to system control



29. Subwoofer

terminal of the power amp (max.



300 mA 12 V DC).

20. Blue/white (6*)



Connect to auto-antenna relay

30. Front speaker

control terminal (max. 300 mA



12 V DC).

21. Blue/white (5*)



31. Rear speaker

The pin position of the ISO



connector will differ depending

32. Perform these connections when

on the type of vehicle. Connect

5* and 6* when Pin 5 is an

using the optional amplifier.

antenna control type. In another

type of vehicle, never connect

5* and 6*.

22. Speaker leads

White:

Front left 

White/black: Front left 

Gray:

Front right 

Gray/black: Front right 

Green:

Rear left  or subwoofer 

Green/black: Rear left  or subwoofer 

Violet:

Rear right  or subwoofer 

Violet/black: Rear right  or subwoofer 

Connecting the units

Note

• When this unit is installed in a vehicle without

ACC (accessory) position on the ignition switch,

26. Power amp

red cable must be wired to the terminal that can

(sold separately)

detect the operation of the ignition key. Otherwise,

battery drain may result.

26. Power amp

(sold separately)

ACC position

No ACC position

• Use this unit in other than the following

conditions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or

malfunction, be sure to follow the directions

below.

— Disconnect the negative terminal of the

battery before installation.

— Secure the wiring with cable clamps or

adhesive tape. To protect the wiring, wrap

adhesive tape around them where they lie

against metal parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors with

insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker's

negative cables.

English

Connecting the units

Connection Diagram

• Control signal is output through blue/white cable

when this unit is powered on. Connect it to an

1. This product

external power amp's system remote control or

2. Rear output

the vehicle's auto-antenna relay control terminal

(max. 300 mA, 12 V DC). If the vehicle is equipped

3. Front output

with a glass antenna, connect it to the antenna

4. Subwoofer output

booster power supply terminal.

5. Wired remote input

• Never connect blue/white cable to external power

Hard-wired remote control adaptor can be

amp's power terminal. Also, never connect

connected (sold separately).

it to the power terminal of the auto antenna.

6. Fuse (10 A)

Otherwise, battery drain or malfunction may

7. Antenna jack

result.

8. Notes

• Black cable is ground. This cable and other

product's ground cable (especially, high-current

• Change the initial setting of this unit (refer

products such as power amp) must be wired

to the operation manual). The subwoofer

separately. Otherwise, fire or malfunction may

output of this unit is monaural.

result if they are accidentally detached.

• When using a subwoofer of 70 W (2 Ω), be

sure to connect with Violet and Violet/black

leads of this unit. Do not connect anything

with Green and Green/black leads.

9. Note

Depending on the kind of vehicle, the function

of 2* and 4* may be different. In this case, be

sure to connect 1* to 4* and 3* to 2*.

10. Connect leads of the same color to each other.

11. Yellow (2*)

Back-up (or accessory)

12. Yellow (1*)

Connect to the constant 12 V supply terminal.

13. Red (4*)

Accessory (or back-up)

14. Red (3*)

Connect to terminal controlled by ignition

switch (12 V DC).

15 Orange/white

Connect to lighting switch terminal.

16. Black (chassis ground)

Connect to a clean, paint-free metal location.

17. ISO connector

Note

In some vehicles, the ISO connector may

be divided into two. In this case, be sure to

connect to both connectors.

English

18. Yellow/black

If you use an equipment with Mute function,

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

19. Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

20. Blue/white (6*)

Connect to auto-antenna relay control terminal

(max. 300 mA 12 V DC).

21. Blue/white (5*)

The pin position of the ISO connector will differ

depending on the type of vehicle. Connect 5*

and 6* when Pin 5 is an antenna control type.

In another type of vehicle, never connect 5*

and 6*.

22. Speaker leads

White: Front left +

White/black: Front left *

Gray: Front right +

Gray/black: Front right *

Green: Rear left + or subwoofer +

Green/black: Rear left * or subwoofer *

Violet: Rear right + or subwoofer +

Violet/black: Rear right * or subwoofer *

23. To rear output

24. To front output

25. To subwoofer output

26. Power amp (sold separately)

27. Connect with RCA cables (sold separately)

28. System remote control

29. Subwoofer

30. Front speaker

31. Rear speaker

32. Perform these connections when using the

optional amplifier.