Pioneer DEH-7300BT 운영 매뉴얼 - 페이지 16

{카테고리_이름} Pioneer DEH-7300BT에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-7300BT 29 페이지. Cd rds receiver
Pioneer DEH-7300BT에 대해서도 마찬가지입니다: 소유자 매뉴얼 (23 페이지), 설치 매뉴얼 (29 페이지)

페이지 인쇄

Section

Operating this unit

SLA (source level adjustment)

SLA (Source Level Adjustment) lets you adjust the vo-

lume level of each source to prevent radical changes

in volume when switching between sources.

! Settings are based on the FM volume level, which

remains unchanged.

! The MW/LW volume level can also be adjusted

with this function.

! When selecting FM as the source, you cannot

switch to SLA.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

3 Press M.C. to confirm the selection.

Initial Settings

Important

PW SAVE (power saving) is cancelled if the vehi-

cle battery is disconnected and will need to be

turned back on once the battery is reconnected.

When PW SAVE (power saving) is off, depending

on connection methods, the unit may continue to

draw power from the battery if your vehicle's igni-

tion doesn't have an ACC (accessory) position.

Press and hold S (SRC/OFF) until the

unit turns off.

Press S (SRC/OFF) and hold until func-

tion name appears in the display.

Turn M.C. to select the initial setting.

After selecting, perform the following proce-

dures to set the initial setting.

FM STEP (FM tuning step)

Normally, the FM tuning step employed by seek tun-

ing is 50 kHz. When AF or TA is on, the tuning step

automatically changes to 100 kHz. It may be prefer-

able to set the tuning step to 50 kHz when AF is on.

! The tuning step remains at 50 kHz during manual

tuning.

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the FM tuning step.

50 KHZ (50 kHz)—100 KHZ (100 kHz)

3 Press M.C. to confirm the selection.

AUTO-PI (auto PI seek)

The unit can automatically search for a different sta-

tion with the same programming, even during preset

recall.

1 Press M.C. to turn Auto PI seek on or off.

AUX (auxiliary input)

Activate this setting when using an auxiliary device

connected to this unit.

1 Press M.C. to turn AUX on or off.

USB (plug and play)

This setting allows you to switch your source to USB/

iPod automatically.

1 Press M.C. to turn the plug and play function on

or off.

ON – When a USB storage device/iPod is con-

nected, depending on the type of device, the

source is automatically switched to USB/iPod

when you turn on the engine. If you disconnect

your USB storage device/iPod, this unit's source

is turned off.

OFF – When a USB storage device/iPod is con-

nected, the source is not switched to USB/iPod

automatically. Please change the source to USB/

iPod manually.

SW CONTROL (rear output setting)

The rear speaker leads output can be used for full-

range speaker or subwoofer connection.

If you switch to REAR-SP:SW, you can connect a rear

speaker lead directly to a subwoofer without using an

auxiliary amp.

Initially, REAR-SP is set for rear full-range speaker

connection (FUL).

1 Press M.C. to display the setting mode.

2 Turn M.C. to change the setting.

REAR-SP: FUL—SW

3 Press M.C. to confirm the selection.

DEMO (demo display setting)

1 Press M.C. to turn the demo display on or off.

SCROLL (scroll mode setting)

When ever scroll is set to ON, recorded text informa-

tion scrolls continuously in the display. Set to OFF if

you prefer the information to scroll just once.

1 Press M.C. to turn the ever scroll on or off.

TITLE (multi-language)