Pioneer DEH-7350BT 소유자 매뉴얼 - 페이지 9

{카테고리_이름} Pioneer DEH-7350BT에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-7350BT 21 페이지. Cd rds receiver

페이지 인쇄

Operating this unit

Function and operation

! The phone book in your cellular phone will be

transferred automatically when the phone is

Refer to PHONE FUNC (phone function) on this

connected to this unit.

! Depending on the cellular phone, the phone

page.

book may not be transferred automatically. In

this case, operate your cellular phone to trans-

fer the phone book. The visibility of this unit

should be on. Refer to VISIBLE (setting the visi-

After selecting, perform the following proce-

bility of this unit) on the previous page.

1 Press M.C. to display SEARCH (alphabetical

dures to set the function.

list).

2 Turn M.C. to select the first letter of the name

A. ANSR (automatic answering)

you are looking for.

1 Press M.C. to turn automatic answering on or

! Press and hold M.C. to select the desired

character type.

3 Press M.C. to display a registered name list.

RING TONE (ring tone select)

4 Turn M.C. to select the name you are looking

for.

1 Press M.C. to turn the ring tone on or off.

5 Press M.C. to display the phone number list.

6 Turn M.C. to select a phone number you want

to call.

Audio Adjustments

! When you find a phone number that you

want to store in memory, press and hold

one of the preset tuning buttons (1 to 6).

! Press one of preset buttons 1 to 6 to recall

the desired preset number.

and press to select AUDIO.

7 Press M.C. to make a call.

PRESET (preset phone numbers)

After selecting, perform the following proce-

dures to set the audio function.

1 Press M.C. to display the setting mode.

2 Use M.C. to select the desired preset number.

FAD/BAL (fader/balance adjustment)

Turn to change the menu option. Press to se-

lect.

1 Press M.C. to display the setting mode.

! You can also press one of the preset num-

2 Press M.C. to cycle between fader (front/rear)

ber buttons 1 to 6 to select a number.

3 Press M.C. to make a call.

3 Turn M.C. to adjust speaker balance.

PHONE FUNC (phone function)

! When the rear output and RCA output setting

You can set A. ANSR and RING TONE from this

menu. For details, refer to Function and operation

on this page.

EQUALIZER (equalizer recall)

Display PHONE FUNC.

Press M.C. to display the function menu.

Turn M.C. to select the function.

off.

Press M.C. to display the main menu.

Turn M.C. to change the menu option

Turn M.C. to select the audio function.

and balance (left/right).

are SW, you cannot adjust front/rear speaker

balance. Refer to SW CONTROL (rear output

and subwoofer setting) on the next page.

Operating this unit

The cut-off frequency and output level can be ad-

1 Press M.C. to display the setting mode.

justed when the subwoofer output is on.

2 Turn M.C. to select the equalizer.

Only frequencies lower than those in the selected

DYNAMIC—VOCAL—NATURAL—CUSTOM

range are outputted from the subwoofer.

—FLAT—POWERFUL

1 Press M.C. to display the setting mode.

3 Press M.C. to confirm the selection.

2 Press M.C. to cycle between the cut-off fre-

TONE CTRL (equalizer adjustment)

! Adjusted equalizer curve settings are stored in

CUSTOM.

1 Press M.C. to display the setting mode.

3 Turn M.C. to select the desired setting.

2 Press M.C. to select BASS (bass)/MID (mid)/

TREBLE (treble).

3 Turn M.C. to adjust the level.

Adjustment range: +6 to -6

SLA (source level adjustment)

LOUDNESS (loudness)

SLA (Source Level Adjustment) lets you adjust the

Loudness compensates for deficiencies in the low-

volume level of each source to prevent radical

and high-frequency ranges at low volume.

changes in volume when switching between sour-

1 Press M.C. to display the setting mode.

ces.

2 Turn M.C. to select the desired setting.

! Settings are based on the FM volume level,

OFF (off)—LOW(low)—HIGH (high)

3 Press M.C. to confirm the selection.

! The AM volume level can also be adjusted with

SUBWOOFER1 (subwoofer on/off setting)

! When selecting FM as the source, you cannot

This unit is equipped with a subwoofer output

which can be turned on or off.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

2 Turn M.C. to select the desired setting.

NORMAL (normal phase)—REVERSE (reverse

3 Press M.C. to confirm the selection.

phase)—OFF (subwoofer off)

3 Press M.C. to confirm the selection.

Initial Settings

SUBWOOFER2 (subwoofer adjustment)

turns off.

appears in the display.

After selecting, perform the following proce-

dures to set the initial setting.

Section

quency and output level of the subwoofer.

Cut-off frequency (Cut-off frequency display

flashes.)—Output level (Output level display

flashes.)

Cut-off frequency: 50HZ—63HZ—80HZ—

100HZ—125HZ

Output level: -24 to +6

which remains unchanged.

this function.

switch to SLA.

Adjustment range: +4 to –4

Press S (SRC/OFF) and hold until the unit

Press M.C. and hold until function name

Turn M.C. to select the initial setting.

<YRD5325-A/N>9