Pioneer DEH-P4700MP 설치 매뉴얼

{카테고리_이름} Pioneer DEH-P4700MP에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-P4700MP 6 페이지. Owner's manual
Pioneer DEH-P4700MP에 대해서도 마찬가지입니다: 소유자 매뉴얼 (34 페이지), 운영 매뉴얼 (4 페이지)

페이지 인쇄

DEH-P4700MP

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Los colores de los cables este producto se conforman

con el código de colores CEMA.

Printed in Thailand

Imprimé en Thaïlande

<CRD3948-A/N> UC

Connecting the Units

Note:

• This unit is for vehicles with a 12-volt battery and

• When this product's source is switched ON, a con-

negative grounding. Before installing it in a recre-

trol signal is output through the blue/white lead.

ational vehicle, truck or bus, check the battery

Connect to an external power amp's system remote

voltage.

control or the car's Auto-antenna relay control ter-

• To avoid shorts in the electrical system, be sure to

minal (max. 300 mA 12 V DC). If the car features

disconnect the ≠ battery cable before beginning

a glass antenna, connect to the antenna booster

installation.

power supply terminal.

• Refer to the owner's manual for details on con-

• When an external power amp is being used with

necting the power amp and other units, then make

this system, be sure not to connect the blue/white

connections correctly.

lead to the amp's power terminal. Likewise, do not

• Secure the wiring with cable clamps or adhesive

connect the blue/white lead to the power terminal

tape. To protect the wiring, wrap adhesive tape

of the auto-antenna. Such connection could cause

around them where they lie against metal parts.

excessive current drain and malfunction.

• Route and secure all wiring so it cannot touch any

• To avoid a short-circuit, cover the disconnected

moving parts, such as the gear shift, handbrake and

lead with insulating tape. Insulate the unused

seat rails. Do not route wiring in places that get

speaker leads without fail. There is a possibility of

hot, such as near the heater outlet. If the insulation

a short-circuit if the leads are not insulated.

of the wiring melts or gets torn, there is a danger of

• To prevent incorrect connection, the input side of

the wiring short-circuiting to the vehicle body.

the IP-BUS connector is blue, and the output side

• Don't pass the yellow lead through a hole into the

is black. Connect the connections of the same col-

engine compartment to connect to the battery. This

ors correctly.

will damage the lead insulation and cause a very

• If this unit is installed in a vehicle that does not

dangerous short.

have an ACC (accessory) position on the ignition

• Do not shorten any leads. If you do, the protection

switch, the red lead of the unit should be connected

circuit may fail to work when it should.

to a terminal coupled with ignition switch ON/OFF

• Never feed power to other equipment by cutting

operations. If this is not done, the vehicle battery

the insulation of the power supply lead of the unit

may be drained when you are away from the vehi-

and tapping into the lead. The current capacity of

cle for several hours. (Fig. 1)

the lead will be exceeded, causing overheating.

• When replacing the fuse, be sure to only use a fuse

of the rating prescribed on this unit.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded or

the left and right ≠ speaker leads are common.

• The black lead is ground. Please ground this lead

separately from the ground of high-current prod-

ucts such as power amps.

ACC position

No ACC position

If you ground the products together and the ground

becomes detached, there is a risk of damage to the

products or fire.

• Speakers connected to this unit must be high-

power with minimum rating of 50 W and imped-

• Cords for this product and those for other prod-

ance of 4 to 8 ohms. Connecting speakers with out-

ucts may be different colors even if they have the

put and/or impedance values other than those

same function. When connecting this product to

noted here may result in the speakers catching fire,

another product, refer to the supplied manuals of

emitting smoke, or becoming damaged.

both products and connect cords that have the

same function.

Multi-CD player

(sold separately)

IP-BUS cable

This product

Rear output

(REAR OUTPUT)

Fuse

Antenna jack

Front output

(FRONT OUTPUT)

Yellow

To terminal always supplied

with power regardless of

ignition switch position.

Red

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

Black (ground)

To vehicle (metal) body.

With a 2 speaker system, do not connect

anything to the speaker leads that are not

connected to speakers.

Fig. 1

Perform these connections when using

the optional amplifier.

Connecting cords

with RCA pin plugs

(sold separately)

IP-BUS input (Blue)

Jack for the Wired Remote Control

Please see the Instruction Manual for the

Wired Remote Control (sold separately).

Blue/white

To system control terminal of the power amp

or Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

System remote control

White

Gray

Front speaker

≠

White/black

Gray/black

Left

Green

Violet

Rear speaker

≠

Green/black

Violet/black

Rear speaker

≠

Left

Front speaker

≠

Power amp

(sold separately)

Power amp

(sold separately)

Front speaker

Right

Rear speaker

≠

Right

Front speaker

Fig. 2