Pioneer DEH-P5100UB - Radio / CD 설치 매뉴얼 - 페이지 5

{카테고리_이름} Pioneer DEH-P5100UB - Radio / CD에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-P5100UB - Radio / CD 8 페이지. Cd rds receiver
Pioneer DEH-P5100UB - Radio / CD에 대해서도 마찬가지입니다: 설치 매뉴얼 (6 페이지), 브로셔 (9 페이지), 빠른 시작 매뉴얼 (8 페이지)

페이지 인쇄

1. Connecting/Diagram

2. Rear output

11. Note

1. This product

Depending on the kind of vehicle,

3. Front output

the function of 3* and 5* may be

different. In this case, be sure to

connect 2* to 5* and 4* to 3*.

4. Subwoofer output

5. Antenna jack

7.Fuse (10 A)

12. Connect leads of the

same color to each other.

13. Cap (1*)

Do not remove cap

if this terminal is

not in use.

14. Yellow (3*)

15. Yellow (2*)

Back-up (or

Connect to the constant

accessory)

12 V supply terminal.

16. Red (5*)

17. Red (4*)

Accessory

Connect to terminal controlled by

(or back-up)

ignition switch (12 V DC).

18. Orange/white

Connect to lighting switch terminal.

19. Black (chassis ground)

Connect to a clean, paint-free metal location.

21. Yellow/black

20. ISO connector

Note

If you use an equipment with Mute

In some vehicles, the ISO connector may be

function, wire this lead to the Audio Mute

divided into two. In this case, be sure to

lead on that equipment. If not, keep the

connect to both connectors.

Audio Mute lead free of any connections.

26.To subwoofer

29.Connect with RCA cables

output

(sold separately)

6. Wired remote input

Hard-wired remote

27.To rear output

control adaptor can

be connected (sold

separately).

28.To front output

8.IP-BUS input (Blue)

10.Multi-CD player

9.IP-BUS cable

(sold separately)

31.System remote control

22. Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

32. Front speaker

23. Blue/white (7*)

Connect to auto-antenna relay control

33. Rear speaker

terminal (max. 300 mA 12 V DC).

24. Blue/white (6*)

The pin position of the ISO

34. Subwoofer

connector will differ depends on the

type of vehicle. Connect 6* and 7*

when Pin 5 is an antenna control

35. Perform these connections when

type. In another type of vehicle,

using the optional amplifier.

never connect 6* and 7*.

36. Notes

25. Speaker leads

• Change the initial setting of this unit (refer to the

White:

Front left

operation manual). The subwoofer output of this unit is

White/black: Front left

monaural.

Gray:

Front right

• When using a subwoofer of 70 W (2 Ω), be sure to

Gray/black: Front right

connect with Violet and Violet/black leads of this unit.

Green:

Rear left

or subwoofer

Do not connect anything with Green and Green/black

Green/black: Rear left

or subwoofer

leads.

Violet:

Rear right

or subwoofer

Violet/black: Rear right

or subwoofer

Connecting the units

Note

30.Power amp

• When this unit is installed in a vehicle without

(sold separately)

ACC (accessory) position on the ignition switch,

red cable must be wired to the terminal that can

detect the operation of the ignition key. Otherwise,

battery drain may result.

30.Power amp

(sold separately)

30.Power amp

(sold separately)

ACC position

No ACC position

• Use this unit in other than the following

conditions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or

malfunction, be sure to follow the directions

below.

32. Front speaker

— Disconnect the negative terminal of the

battery before installation.

— Secure the wiring with cable clamps or

adhesive tape. To protect the wiring, wrap

adhesive tape around them where they lie

33. Rear speaker

against metal parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

34. Subwoofer

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors with

insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker's

negative cables.

English

Connecting the units

• Control signal is output through blue/white cable

Connection Diagram

when this unit is powered on. Connect it to an

1. This product

external power amp's system remote control or

2. Rear output

the vehicle's auto-antenna relay control terminal

(max. 300 mA, 12 V DC). If the vehicle is equipped

3. Front output

with a glass antenna, connect it to the antenna

4. Subwoofer output

booster power supply terminal.

5. Antenna jack

• Never connect blue/white cable to external power

6. Wired remote input

amp's power terminal. Also, never connect

Hard-wired remote control adaptor can be

it to the power terminal of the auto antenna.

connected (sold separately).

Otherwise, battery drain or malfunction may

7. Fuse (10 A)

result.

• IP-BUS connectors are color-coded. Be sure to

8. IP-BUS input (Blue)

connect connectors of the same color.

9. IP-BUS cable

• Black cable is ground. This cable and other

10. Multi-CD player (sold separately)

product's ground cable (especially, high-current

11. Note

products such as power amp) must be wired

Depending on the kind of vehicle, the function

separately. Otherwise, fire or malfunction may

of 3* and 5* may be different. In this case, be

result if they are accidentally detached.

sure to connect 2* to 5* and 4* to 3*.

12. Connect leads of the same color to

each other.

13. Cap (1*)

Do not remove cap if this terminal is not in use.

14. Yellow (3*)

Back-up (or accessory)

15. Yellow (2*)

Connect to the constant 12 V supply terminal.

16. Red (5*)

Accessory (or back-up)

17. Red (4*)

Connect to terminal controlled by ignition

switch (12 V DC).

18. Orange/white

Connect to lighting switch terminal.

19. Black (chassis ground)

Connect to a clean, paint-free metal location.

20. ISO connector

Note

In some vehicles, the ISO connector may

be divided into two. In this case, be sure to

connect to both connectors.

21. Yellow/black

If you use an equipment with Mute function,

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

22. Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

23. Blue/white (7*)

Connect to auto-antenna relay control terminal

(max. 300 mA 12 V DC).

English

24. Blue/white (6*)

The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6*

and 7* when Pin 5 is an antenna control type.

In another type of vehicle, never connect 6*

and 7*.

25. Speaker leads

White: Front left

White/black: Front left

Gray: Front right

Gray/black: Front right

Green: Rear left

or subwoofer

Green/black: Rear left

or subwoofer

Violet: Rear right

or subwoofer

Violet/black: Rear right

or subwoofer

26. To subwoofer output

27. To rear output

28. To front output

29. Connect with RCA cables (sold separately)

30. Power amp (sold separately)

31. System remote control

32. Front speaker

33. Rear speaker

34. Subwoofer

35. Perform these connections when using the

optional amplifier.

36. Notes

• Change the initial setting of this unit (refer

to the operation manual). The subwoofer

output of this unit is monaural.

• When using a subwoofer of 70 W (2 Ω), be

sure to connect with Violet and Violet/black

leads of this unit. Do not connect anything

with Green and Green/black leads.