Pioneer DEH-P5200HD 운영 매뉴얼 - 페이지 15

{카테고리_이름} Pioneer DEH-P5200HD에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-P5200HD 37 페이지. Cd receiver
Pioneer DEH-P5200HD에 대해서도 마찬가지입니다: 설치 매뉴얼 (6 페이지)

페이지 인쇄

Operating this unit

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the vo-

lume level of each source to prevent radical changes

in volume when switching between sources.

! When selecting FM as the source, you cannot

switch to SLA.

! Settings are based on the FM volume level, which

remains unchanged.

Before adjusting source levels, compare the FM

volume level with the level of the source you wish

to adjust.

! The AM volume level can also be adjusted with

source level adjustments.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

3 Press M.C. to confirm the selection.

Note

Operation is complete even if the menu is can-

celled before being confirmed.

Initial Settings

Press SRC/OFF and hold until the unit

turns off.

Press M.C. and hold until the initial set-

ting menu appears in the display.

Turn M.C. to select the initial setting.

After selecting, perform the following proce-

dures to set the initial setting.

Clock (setting the clock)

1 Press M.C. to display the setting mode.

2 Press M.C. to select the segment of the clock dis-

play you wish to set.

Hour—Minute

As you select segments of the clock display, the

selected segment flashes.

3 Turn M.C. to adjust the clock.

Clock (clock on/off setting)

1 Press M.C. to turn the clock display on or off.

AUX1/AUX2 (auxiliary input setting)

Activate this setting when using auxiliary device con-

nected to this unit.

1 Press M.C. to turn AUX on or off.

USB PnP (plug and play)

This setting allows you to switch your source to USB/

USB-iPod automatically.

1 Press M.C. to turn the plug and play on or off.

ON – When USB storage device/iPod is con-

nected, the source is automatically switched to

USB/USB-iPod. If you disconnect your USB sto-

rage device/iPod, this unit's source is turned off.

OFF – When USB storage device/iPod is con-

nected, the source is not switched to USB/USB-

iPod automatically. Please change the source to

USB/USB-iPod manually.

Brightness (display brightness setting)

1 Press M.C. to display the setting mode.

2 Turn M.C. to switch the brightness setting.

High (high)—Low (low)

3 Press M.C. to confirm the selection.

SW control (rear output and subwoofer setting)

The rear speaker leads output (Rear SP) and RCA out-

put (Preout) of this unit can be used for full-range

speaker (Rear SP :FULL/Preout :Rear) or subwoofer

(Rear SP :SUBW/Preout :SUBW) connection. If you

switch to Rear SP :SUBW, you can connect a rear

speaker lead directly to a subwoofer without using an

auxiliary amp.

Initially, Rear SP is set for rear full-range speaker con-

nection (FULL). When Rear SP :FULL is selected, you

can connect the RCA output to a subwoofer. In this

case, you can select whether to use the subwoofer

controller's (low pass filter, phase) built-in Preout :

SUBW or the auxiliary Preout :Rear.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between as following:

Rear SP/Preout—FULL (SUBW)/SUBW(Rear)

3 Turn M.C. to change the setting.

Rear SP: FULL—SUBW

Preout: SUBW—Rear

! Even if you change this setting, there is no

output unless you turn the subwoofer output

on (refer to SW setting 1 (subwoofer on/off

setting) on the previous page).

! If you change this setting, subwoofer output

in the audio menu will return to the factory

settings.

DEMO (demo display setting)

1 Press M.C. tp turn the demo display on or off.

Section