Pioneer MVH-1490UB 소유자 매뉴얼 - 페이지 8

{카테고리_이름} Pioneer MVH-1490UB에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer MVH-1490UB 17 페이지. Rds media center receiver

페이지 인쇄

Section

Operating this unit

S.RTRV (sound retriever)

Automatically enhances compressed audio and

restores rich sound.

1 Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on the previous page.

Audio adjustments

Press M.C. to display the main menu.

Turn M.C. to change the menu option

and press to select AUDIO.

Turn M.C. to select the audio function.

After selecting, perform the following proce-

dures to set the audio function.

FAD/BAL (fader/balance adjustment)

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between fader (front/rear)

and balance (left/right).

3 Turn M.C. to adjust speaker balance.

! When the rear output and RCA output setting

are SW, you cannot adjust front/rear speaker

balance. Refer to REAR-SP (rear output setting)

on this page. Refer to PREOUT (preout setting)

on the next page.

PRESET EQ (equalizer recall)

1 Press M.C. to display the setting mode.

2 Turn M.C. to select the equalizer.

DYNAMIC—VOCAL—NATURAL—CUSTOM

—FLAT—POWERFUL

3 Press M.C. to confirm the selection.

! You can also switch the equalizer by pressing

repeatedly.

TONE CTRL (equalizer adjustment)

! Adjusted equalizer curve settings are stored in

CUSTOM.

1 Press M.C. to display the setting mode.

2 Press M.C. to select BASS (bass)/MID (mid)/

TREBLE (treble).

3 Turn M.C. to adjust the level.

Adjustment range: +6 to –6

LOUD (loudness)

Loudness compensates for deficiencies in the low-

frequency and high-frequency ranges at low vol-

ume.

1 Press M.C. to select the desired setting.

OFF (off)—LOW(low)—HI (high)

SUB.W (subwoofer on/off setting)

This unit is equipped with a subwoofer output

which can be turned on or off.

1 Press M.C. to select the desired setting.

NOR (normal phase)—REV (reverse phase)—

OFF (subwoofer off)

SUB.W CTRL (subwoofer adjustment)

The cut-off frequency and output level can be ad-

justed when the subwoofer output is on.

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

! When you select OFF in SUB.W, you cannot se-

lect this function. For details, refer to SUB.W

(subwoofer on/off setting) on this page.

1 Press M.C. to display the setting mode.

2 Press M.C. to cycle between the cut-off fre-

quency and output level of the subwoofer.

Cut-off frequency (Cut-off frequency display

flashes.)—Output level (Output level display

flashes.)

3 Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—

100HZ—125HZ

Output level: –24 to +6

Operating this unit

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the

volume level of each source to prevent radical

changes in volume when switching between sour-

ces.

! Settings are based on the FM volume level,

which remains unchanged.

! The MW volume level can also be adjusted

with this function.

! When selecting FM as the source, you cannot

switch to SLA.

1 Press M.C. to display the setting mode.

2 Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

3 Press M.C. to confirm the selection.

Initial settings

Press and hold SRC/OFF until the unit

turns off.

Press M.C. and hold until function name

appears in the display.

Turn M.C. to select the initial setting.

After selecting, perform the following proce-

dures to set the initial setting.

CLOCK SET (setting the clock)

1 Press M.C. to display the setting mode.

2 Press M.C. to select the segment of the clock

display you wish to set.

Hour—Minute

3 Turn M.C. to adjust the clock.

FM STEP (FM tuning step)

Normally, the FM tuning step employed by seek

tuning is 50 kHz. When AF or TA is on, the tuning

step automatically changes to 100 kHz. It may be

preferable to set the tuning step to 50 kHz when

AF is on.

! The tuning step remains at 50 kHz during man-

ual tuning.

1 Press M.C. to select the FM tuning step.

50 (50 kHz)—100 (100 kHz)

MW STEP (MW tuning step)

The MW tuning step can be switched between

9 kHz and 10 kHz.

1 Press M.C. to select the MW tuning step.

9 (9 kHz)—10 (10 kHz)

AUTO-PI (auto PI seek)

The unit can automatically search for a different

station with the same programming, even during

preset recall.

1 Press M.C. to turn Auto PI seek on or off.

AUX (auxiliary input)

Activate this setting when using an auxiliary de-

vice connected to this unit.

1 Press M.C. to turn AUX on or off.

USB PNP (plug and play)

This setting allows you to switch your source to

USB/iPod automatically.

1 Press M.C. to turn the plug and play function

on or off.

ON – When a USB storage device/iPod is con-

nected, depending on the type of device, the

source is automatically switched to USB/iPod

when you turn on the engine. If you disconnect

your USB storage device/iPod, this unit's

source is turned off.

OFF – When a USB storage device/iPod is con-

nected, the source is not switched to USB/

iPod automatically. Please change the source

to USB/iPod manually.

REAR-SP (rear output setting)