Pioneer RX-Z16 서비스 매뉴얼 - 페이지 43
{카테고리_이름} Pioneer RX-Z16에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer RX-Z16 45 페이지. Stereo double cassette deck receiver
페이지 인쇄
| FRONT PANEL FACILITIES
|
¢ Illustration shows model RX-Z36.
@®: [Tuner Section]
@ Remote sensor window (REMOTE SENSOR)
@ FM MONO button
Turn onwhen there is too much noise during reception of FM stereo
broadcasts. The reproduced sound will become monaural but noise
will be reduced.
® Display section
Shows received broadcast frequency or station call no.
FM and MHz light: FM reception.
AM and kHz light: AM reception.
Channel display: station call no. display
@ FM MONO indicator
Lights when the FM MONO button is set to ON. When this indicator is
lit, FM stereo broadcasts are reproduced monaurally.
® STEREO indicator
Lights when an FM stereo broadcast is received (FM MONO button
set to OFF).
© TUNED indicator
Lights when a broadcast is received and tuned in well.
@ MEMORY button
Used for memorizing stations
STATION CALL button
Use to switch between frequency display and station no. display.
During frequency display, you can use the TUNING + and — buttons
@ to raise or lower the received frequency.
During station no. display, you can use the TUNING + and — buttons
@ to raise or lower the received station number.
@ BAND selector button
Each time this button is pressed, FM or AM reception is selected
alternately.
@ TUNING +, — (UP, DOWN) buttons
Used for locating stations.
Use "—" button for lower, and "++" button for higher station no. or
frequencies.
RX-Z36.
RX-Z16
®: [Amplifier and Graphic Equalizer Section]
@ Graphic equalizer controls
@ Spectrum analyzer display (RX-Z36)
Level indicator (RX-Z16)
@ STEREO
WIDE
button (RX-Z16), SURROUND
&
STEREO WIDE button (RX-Z36)/indicator
By turning this switch ON, you can enjoy surround reproduction
when rear speakers are used (RX-Z36 only).
By turning this switch ON, you can enjoy SURROUND
& STEREO
WIDE
reproduction
with
greater
left-right
spread
when
rear
speakers are not used.
The indicator lights when SURROUND & STEREO WIDE is on.
NOTE:
In the case of monaural source, SURROUND & STEREO WIDE effects
cannot be obtained.
@® VOLUME control
® POWER STANDBY/ON switch /STANDBY
indicator
This is the switch for electric power.
ON
: When set to the ON position, power is supplied and the
unit becomes operational.
STANDBY
: When set to the STANDBY position, the main power
flow is cut and the unit is no longer fully operational. A
minute
flow of power
feeds
the
unit to maintain
operation readiness.
The unit is in STANDBY
when
only the STANDBY
indicator above the POWER switch is lit.
Press the SLEEP
button on the remote
control to
operate the sleep timer, and the STANDBY indicator
flashes to show that the sleep timer is operating.
@® SUPER BASS button/indicator (RX-Z36 only)
Set to ON to augment bass frequency response.
@ INPUT SELECTOR buttons
[TUNER]
Press to listen to radio broadcast.
[TAPE]
Press to listen to cassette tape.
[CD]
Press to listen to a CD player connected to the CD jacks.
[PHONO]
Press to play records on a turntable connected to the PHONO jacks.
MIC LEVEL control
Used for adjusting the volume of the microphone.
@ MIC (Microphone) jack
This is a standard jack for connecting a microphone.
55