Pioneer Super Tuner IIID MVH-P8200BT 설치 매뉴얼

{카테고리_이름} Pioneer Super Tuner IIID MVH-P8200BT에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer Super Tuner IIID MVH-P8200BT 8 페이지. Media center receiver

페이지 인쇄

1. Connecting the Unit

MEDIA CENTER RECEIVER

AUTORADIO MULTIMEDIA

RECEPTOR Y CENTRO DE COMUNICACIONES

MVH-P8200BT

MVH-P8200

Installation Manual

Manuel d'installation

Manual de instalación

Printed in Thailand

Imprimé en Thaïlande

CRD4472-A/N

> UC

Connecting the unit

English

WARNING

• To avoid the risk of accident and the potential

• Use speakers over 50 W (output value) and

violation of applicable laws, no viewing of front

between 4 W to 8 W (impedance value). Do not use

seat video should ever occur while the vehicle is

1 W to 3 W speakers for this unit.

being driven.

• The black cable is ground. When installing this

• In some countries or states the viewing of images

unit or power amp (sold separately), make sure

on a display inside a vehicle even by persons

to connect the ground wire first. Ensure that

other than the driver may be illegal. Where such

the ground wire is properly connected to metal

regulations apply, they must be obeyed.

parts of the car's body. The ground wire of the

power amp and the one of this unit or any other

device must be connected to the car separately

with different screws. If the screw for the ground

CAUTION

wire loosens or falls out, it could result in fire,

generation of smoke or malfunction.

• PIONEER does not recommend that you

install or service your display yourself.

Ground wire

POWER AMP

Installing or servicing the product may

expose you to risk of electric shock or other

hazards. Refer all installation and servicing

of your display to authorized Pioneer service

personnel.

• Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wiring

to remain exposed.

Other devices

• Do not drill a hole into the engine

Metal parts of car's body

(Another electronic

compartment to connect the yellow lead

device in the car)

of the unit to the vehicle battery. Engine

vibration may eventually cause the insulation

to fail at the point where the wire passes from

Important

the passenger compartment into the engine

compartment. Take extra care in securing the

• When this unit is installed in a vehicle without

wire at this point.

ACC (accessory) position on the ignition switch,

• Make sure that wires will not interfere with

red cable must be wired to the terminal that can

moving parts of the vehicle, such as the

detect the operation of the ignition key. Otherwise,

gearshift, parking brake or seat sliding

battery drain may result.

mechanism.

• Do not shorten any leads. If you do, the

protection circuit may fail to work properly.

WARNING

LIGHT GREEN LEAD AT POWER CONNECTOR

IS DESIGNED TO DETECT PARKED STATUS

ACC position

No ACC position

AND MUST BE CONNECTED TO THE POWER

SUPPLY SIDE OF THE PARKING BRAKE SWITCH.

• Use this unit with a 12-volt battery and negative

IMPROPER CONNECTION OR USE OF THIS

grounding only. Failure to do so may result in a

LEAD MAY VIOLATE APPLICABLE LAW AND MAY

fire or malfunction.

RESULT IN SERIOUS INJURY OR DAMAGE.

• To prevent short-circuit, overheating or

malfunction, be sure to follow the directions

below.

— Disconnect the negative terminal of the

battery before installation.

— Secure the wiring with cable clamps or

adhesive tape. To protect the wiring, wrap

adhesive tape around them where they lie

against metal parts.

Connecting the unit

English

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.

— Cover any disconnected cable connectors with

insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker's

negative cables.

• When this unit is on, control signals are sent

through the blue/white cable. Connect this cable

to the system remote control of an external power

amp or the vehicle's auto-antenna relay control

terminal (max. 300 mA 12 V DC).

If the vehicle is equipped with a glass antenna,

connect it to the antenna booster power supply

terminal.

• Never connect the blue/white cable to the power

terminal of an external power amp.

Also, never connect it to the power terminal of the

auto antenna. Doing so may result in battery drain

or a malfunction.

• IP-BUS connectors are color-coded. Be sure to

connect connectors of the same color.