Pioneer CT-W208R - Dual Cassette Deck 사용 설명서 - 페이지 25
{카테고리_이름} Pioneer CT-W208R - Dual Cassette Deck에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer CT-W208R - Dual Cassette Deck 32 페이지. Stereo double
Pioneer CT-W208R - Dual Cassette Deck에 대해서도 마찬가지입니다: 사용 설명서 (20 페이지), 카탈로그 (10 페이지), 사양 (1 페이지), 서비스 매뉴얼 (34 페이지), 서비스 매뉴얼 (34 페이지)
페이지 인쇄
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks
listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.
Symptom
POWER
÷ The power plug is disconnected.
Cannot turn power on.
÷ The component (stereo amplifier, audio timer,
CASSETTE DOOR
The door does not open. ÷ The deck is not in stop mode (tape is moving).
The door does not close. ÷ The cassette is not properly loaded.
PLAYBACK
Immediately stops.
The level meter
does not work.
No sound
RECORDING
The recording indicator
does not light up.
The level meter
does not work.
Immediately stops.
Cannot record
No sound
REC LEVEL control
does not function.
Cause
etc.) to which the power cord is connected is
off.
÷ Power was turned off with the tape moving.
÷ The tape is completely wound.
÷ The tape is slack.
÷ The tape is blank.
÷ The tape head is dirty.
÷ The amplifier input selector is not correctly set. ÷ Set the amplifier input selector correctly.
÷ The amplifier volume level setting is too low.
÷ Connection problems (wrong connection,
cord removed, poor contact, broken wire.)
÷ The cassette erasure prevention tabs are
broken.
÷ REC LEVEL control is set too low.
÷ The amplifier is not delivering a recording
signal (from the tuner, CD player, etc.).
÷ Wrong connection, connection cord removed,
poor contact, broken wire.
÷ The tape is completely wound.
÷ The tape is slack.
÷ The head is dirty.
÷ Connection problems (wrong connection,
cord removed, poor contact, broken wire.)
÷ The tape is being copied.
Remedy
÷ Connect the power plug.
÷ Turn the stereo amplifier or audio
timer on.
÷ Press the stop (7) button.
÷ Turn power on.
÷ Reinsert the cassette.
÷ Play back in the opposite direction.
÷ Rewind the tape.
÷ Take up the slack (see page 6).
÷ Replace the blank tape with a
prerecorded one.
÷ Clean the heads (see page 7).
÷ Turn the amplifier volume control up.
÷ Connect securely (see page 8).
÷ Replace the cassette with one
whose tabs are intact.
÷ Cover the hole over the tab
(see page 6).
÷ Turn REC LEVEL control up
(see page 21).
÷ Set the amplifier recording output
selector correctly.
÷ Check connections (see page 8).
÷ Record in the opposite direction.
÷ Rewind the tape.
÷ Take up the slack (see page 6).
÷ Clean the head (see page 7).
÷ Check that the recording and
playback connection cords are
connected correctly. (see page 8).
÷ Set the amplifier selector correctly.
÷ When recording is finished,
REC LEVEL control will function.
25
En
En/Fr