Pioneer DEH-8350SD 소유자 매뉴얼 - 페이지 9

{카테고리_이름} Pioneer DEH-8350SD에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-8350SD 20 페이지. Cd rds receiver

페이지 인쇄

Operating this unit

Loudness compensates for deficiencies in the low-

and high-frequency ranges at low volume.

1 Press M.C. to turn loudness on or off.

2 Push M.C. left or right to select the desired set-

ting.

Low (low)—Mid (mid)—High (high)

Sub W.1 (subwoofer on/off setting)

This unit is equipped with a subwoofer output

which can be turned on or off.

1 Press M.C. to turn subwoofer output on or off.

2 Push M.C. left or right to select the phase of

subwoofer output.

Push M.C. left to select reverse phase and Re-

verse appears in the display. Push M.C. right

to select normal phase and Normal appears in

the display.

Sub W.2 (subwoofer adjustment)

The cut-off frequency and output level can be ad-

justed when the subwoofer output is on.

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

1 Push M.C. left or right to select the cut-off fre-

quency.

50Hz—63Hz—80Hz—100Hz—125Hz

2 Push M.C. up or down to adjust the output

level of the subwoofer.

Each time M.C. is pushed up or down, sub-

woofer level increases or decreases. +6 to -24

is displayed as the level is increased or de-

creased.

Bass (bass boost)

1 Push M.C. up or down to select a desired level.

0 to +6 is displayed as the level is increased or

decreased.

HPF (high pass filter adjustment)

When you do not want low sounds from the sub-

woofer output frequency range to play from the

front or rear speakers, turn on the HPF (high pass

filter). Only frequencies higher than those in the

selected range are output from the front or rear

speakers.

1 Press M.C. to turn high pass filter on or off.

2 Push M.C. left or right to select the cut-off fre-

quency.

50Hz—63Hz—80Hz—100Hz—125Hz

SLA (source level adjustment)

SLA (Source Level Adjustment) lets you adjust the

volume level of each source to prevent radical

changes in volume when switching between sour-

ces.

! When selecting FM as the source, you cannot

switch to SLA.

! Settings are based on the FM volume level,

which remains unchanged.

! The AM volume level can also be adjusted with

this function.

1 Push M.C. up or down to adjust the source vol-

ume.

Adjustment range: +4 to –4

Initial Settings

1 Function display

! Shows the function status.

Press and hold SRC/OFF until the unit

turns off.

Operating this unit

Press M.C. and hold until the initial set-

ting menu appears in the display.

Turn M.C. to select the initial setting.

After selecting, perform the following proce-

dures to set the initial setting.

Language select (multi-language)

For your convenience, this unit equips multiple

language display. You can select the language

best suited to your first language.

1 Press M.C. to select the language.

English—Español—Português

Calendar (setting the date)

1 Push M.C. left or right to select the segment of

the calendar display you wish to set.

Year—Day—Month

2 Push M.C. up or down to set the date.

Clock (setting the clock)

1 Push M.C. left or right to select the segment of

the clock display you wish to set.

Hour—Minute

2 Push M.C. up or down to put a clock right.

! You can match the clock to a time signal by

pressing M.C.

! If 00 to 29, the minutes are rounded down.

(e.g., 10:18 becomes 10:00.)

! If 30 to 59, the minutes are rounded up. (e.

g., 10:36 becomes 11:00.)

EngineTime alert (elapsed time display setting)

This setting allows you to measure the length of

time that elapses from when the machine is

turned on and display the amount of elapsed time

per set period.

Also, you will hear alarm.

1 Press M.C. to select your favorite setting.

OFF—15Minutes—30Minutes

FM step (FM tuning step)

The FM tuning step employed by seek tuning can

be switched between 100 kHz, the preset step, and

50 kHz.

If seek tuning is performed in 50 kHz steps, sta-

tions may be tuned in imprecisely. Tune in the sta-

tions with manual tuning or use seek tuning

again.

1 Press M.C. to select the FM tuning step.

50kHz (50 kHz)—100kHz (100 kHz)

AM STEP (AM tuning step)

The AM tuning step can be switched between 9

kHz, the preset step, and 10 kHz. When using the

tuner in North, Central or South America, reset

the tuning step from 9 kHz (531 kHz to 1 602 kHz

allowable) to 10 kHz (530 kHz to 1 640 kHz allow-

able).

1 Press M.C. to select the AM tuning step.

10 KHZ (10 kHz)—9 KHZ (9 kHz)

USB plug&play (plug and play)

This setting allows you to switch your source to

USB/iPod automatically.

1 Press M.C. to turn the plug and play function

on or off.

! ON – When USB storage device/iPod is

connected, the source is automatically

switched to USB/iPod. If you disconnect

your USB storage device/iPod, this unit's

source is turned off.

! OFF – When USB storage device/iPod is

connected, the source does not switch to

USB/iPod automatically. Please manually

change the source to USB/iPod.

Warning tone (warning tone setting)

If the front panel is not detached from the head

unit within four seconds of turning off the ignition,

a warning tone sounds. You can turn off the warn-

ing tone.

1 Press M.C. to turn the warning tone on or off.

AUX (auxiliary input)

Section