Pioneer Elite VSX-51 사용 설명서 - 페이지 46
{카테고리_이름} Pioneer Elite VSX-51에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer Elite VSX-51 49 페이지. 7.1-channel a/v receiver featuring airplay, dlna certified (1.5), internet radio with vtuner, made for ipad certification and 2-zone audio and video
Pioneer Elite VSX-51에 대해서도 마찬가지입니다: 사양 (2 페이지)
페이지 인쇄
VSX-43900S/VSX-4850S/VSX-51
REMOTE CONTROL OPERATION
to call up the remote control codes of other manufacturers.
Preset
remote control signals in the table, however, may not always enable
operation. If operation is not possible, switch to the LEARN mode, and
learn signals from the VCR or TV remote control. Numbers in parenthesis
indicate a reduced possibility of operation.
1. Remove the battery compartment cover.
2. While pressing the M-CLR button inside the cover, press the button
for the CONTROL MODE (for exampie VCR 1} you want to initialize.
«® For example, if you initialize VCR 1 using the method mentioned
above, the CONTROL MODE button lights for about one second,
and the VCR 1 operation buttons are initialized.
Manufacturer
Tv
VCR
RCA
1, (10)
{1}, (6)
ZENITH
3
(3), (4)
I
i
GE
8, (11), (1)
(4), (8)
Initializing the entire memory
SONY
4
4
1. Remove the battery compartment cover.
TOSHIBA
5
5, (9)
2. While pressing the M-CLR button inside the cover, press the RESET
HITACHI
6, (10)
6
button,
PHILIPS
7
~
* Do not release the M-CLR button before releasing the RESET
Jvc
a
7
button. While pressing the M-CLR button, press the RESET button,
PANASONIC
8
8
and quickly release.
MITSUBISHI
9, (10}
9
{nitialization is not possible if the buttons are pressed in the reverse
SANYO
|
10, (12)
order.
SHARP
(2)
2
* All the CONTROL MODE operation buttons are initialized, and data
GOLD STAR
{10)
(4)
in the MULTL-COMMAND button is cleared.
Shokan
(7), (10), (12)
(8), (9)
T
button
wey
M-CLR button
LVANIA
(7), (10), (12)
(8), (3)
es
Wz Z
QUASER
8
8
(
FISHER
-
12, (10)
WARD'S
(2), (7), (10), (11)
(2)
TROUBLESHOOTING |
Symptom
Cause
Remedy
Power does not come on even
* Power cord is disconnected.
* Connect cord securely,
when POWER switch is pressed. | * instances are rare, but the problem may be due
* Unplug the power cord of the unit from the AC
|
to the operation of the protector circuit.
wail outlet, then plug it in again.
|
Control was not possible
* Static electricity affected the unit when the air
* Unplug the power cord of the unit from the AC
regardiess of what operation
was dry, such as in winter.
wall outlet, then plug it in again.
button was pressed.
lf static electricity is pronounced, it is
recommended that you operate the unit using
|
the remote control unit.
No sound is produced, even
* Connections are incorrect.
* Consult page 8 —
14 and perform connections
when the INPUT SELECTOR
correctly.
button is selected.
* The MUTING button is pressed.
* Press the MUTING button to cancel the MUTING
effect.
Raise volume.
* VOLUME is turned down.
* Speaker connecting wires are disconnected
* Connect wires to terminals securely.
| from speaker terminals.
* One or both of the input cords are disconnected.
| * Connect input cords securely,
° TAPE 2 MONITOR button is in the ON position.
* Press the button again to the OFF position.
* The SPEAKERS button is OFF.
* Switch the SPEAKERS button ON.
No picture is produced, even
* Connections are incorrect.
* Consult page 8 ~
14 and perform connections
when the INPUT SELECTOR
| correctly.
i
button is selected.
* The V- SIGNAL SELECTOR is not set properly.
* Set correctly.
* The VCR and the selected INPUT SELECTOR
* Press the correct button.
button are not correct.
46
< ARB1318 >