Pioneer X-HM81-S 사용 설명서 - 페이지 34

{카테고리_이름} Pioneer X-HM81-S에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer X-HM81-S 42 페이지. Network cd receiver system
Pioneer X-HM81-S에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (33 페이지)

페이지 인쇄

 The broadcasts from an Internet Radio station are stopped or

interrupted. Some Internet radio stations on the list of Internet

Radio stations for this receiver (page 30) may occasionally not

be available for listening.

 Cannot pause at Music Server/DMR.

 For some DLNA server software/NAS, or file formats being

played, you many not be able to pause. Please contact the

DLNA server software manufacturer or NAS manufacturer that

you are using.

Wireless LAN

 Network cannot be accessed via wireless LAN.

 Is Network Type set to Auto and the LAN cable connected to

the receiver? Switch Network Type to Wireless or disconnect

the LAN cable from the receiver, then restart the receiver. If

Network Type is set to Auto and the LAN cable is connected

to the receiver, the receiver recognizes the Network Type as

Wired.

 This receiver and base receiver (wireless LAN router, etc.) are

too far apart or there is an obstacle between them. Improve the

wireless LAN environment by moving the receiver and base

receiver closer together, etc.

 This receiver and base receiver (wireless LAN router, etc.) are

too far apart or there is an obstacle between them. Improve the

wireless LAN environment by moving the receiver and base

receiver closer together, etc.

 There is a microwave oven or other device generating

electromagnetic waves near the wireless LAN environment.

Use the system in a place away from microwave ovens or

others device generating electromagnetic waves. Avoid using

devices generating electromagnetic waves as much as

possible when using the system with the wireless LAN.



Multiple wireless devices are connected to the wireless

LAN router.

When connecting multiple wireless devices, their

IP addresses must be changed.

 Wireless LAN connections cannot be established between

the receiver and base receiver (wireless LAN router, etc.).

The receiver must be set in order to establish wireless LAN

connections. See Connecting using wireless LAN on

page 10.

 The IP address settings of the receiver does not match the

settings of the wireless LAN router, etc. Check the IP address

settings of the receiver (including the DHCP setting). If the

receiver's DHCP setting is on, turn the receiver's power off,

then turn the power back on. Check that the IP address of the

receiver matches the settings of the wireless LAN router, etc. If

the receiver's DHCP setting is off, set an IP address matching

the network of the base receiver (wireless LAN router, etc.). For

example, if the wireless LAN router's IP address is

"192.168.1.1", set the receiver's IP address to "192.168.1.XXX"

(*1), the subnet mask to "255.255.255.0", the gateway and DNS

to "192.168.1.1".

*1) Set the "XXX" in "192.168.1.XXX" to a number between 2

and 248 that is not assigned to other devices.

 The access point is set to conceal the SSID.

SSID may not be displayed on the access point list screen.

If not, set the SSID, etc., by making the wireless LAN

settings on the receiver manually.

 The access point's security settings use WEP 152-bit length

code key or shared key authentication. The receiver does not

support WEP 152-bit length code key or shared key

authentication.

Firmware Update

Use this procedure to update the receiver's software. You can

update the software via a USB storage device.

Updating via a USB storage device is performed by

downloading the update file from a computer, reading this file

onto a USB storage device then inserting the USB storage

device into the USB port on the receiver's front panel.

If an update file is provided on the Pioneer website, download

it onto your computer. When downloading an update file from

the Pioneer website onto your computer, the file will be in ZIP

format. Unzip the ZIP file before saving it on the USB storage

device. If there are any old downloaded files or downloaded

files for other models on the USB storage device, delete them.

Important

•

DO NOT unplug the power cord during updating.

•

When updating via a USB storage device, do not

disconnect the USB storage device.

Press USB to select USB as the input source.

USB is shown on the display.

Press SETUP.

The Initial Setup screen is displayed on the display.

Select Option Setting  Firmware Update  Start,

then press ENTER.

In this case, the

To update, select OK.

The updating screen appears and updating starts.

The receiver will reboot when the update is completed,

and the display will show the input function before the

update.

Firmware Update messages

Status messages

File Not Found.

Firmware Update using Safari browser

You can update this receiver's firmware via Apple Safari

browser. Download the latest firmware at Pioneer website.

Be sure this receiver and your computer are connected

to the same wired or wireless network.

Launch Safari on your computer.

Additional information

Firmware Update

Start

Cancel

Description

No update file was found on the USB

storage device. Store the file in the USB

storage device's root directory.