Pioneer X-HM82D-K 빠른 시작 매뉴얼 - 페이지 5
{카테고리_이름} Pioneer X-HM82D-K에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer X-HM82D-K 37 페이지.
페이지 인쇄
Connecting to network
The following is one example of how to connect to a network.
For other connections, please refer to the attached Operating Instructions (CD-ROM)
Connecting this receiver using
wired LAN
1. Be sure your router supports DHCP server
function.
2. Use the LAN cable to connect this receiver
and your router.
3. Plug the power cord into an AC outlet.
Press STANDBY/ON.
B: Connecting to a router with WPS-
PBC function
1. Be sure the LAN cable is not connected to
the receiver.
2. Plug the power cord into an AC outlet.
Press STANDBY/ON.
3. Press NET SERVICE SETUP on the
remote control.
4. Select Network Setting WPS.
5. Useto select PBC (Push Button
Confi guration) and then press ENTER.
6. Press the WPS button on the router.
If the connection does not succeed, refer
to Operating Instructions (CD-ROM) (page
44) and redo the setting again.
PBC (Push Button Confi guration)
• The wireless connection setting is
automatically confi gured by pressing
the WPS button on the WPS compatible
wireless LAN device.
Connecting this receiver using
wireless LAN
A: Connection settings using an iOS
device (with iOS 5.0 or later)
You can apply iPod/iPhone/iPad (iOS device
with iOS ver 5.0 or later)'s Wi-Fi settings to
this receiver.
1. Be sure the LAN cable is not connected to
the receiver. Unlock your iPod/iPhone/iPad.
2. Plug the power cord into an AC outlet.
Press STANDBY/ON.
3. Unlock your iPod/iPhone/iPad. Check that
the Wi-Fi mark is displayed on the iOS
device screen.
Share Wi-Fi Settings?
C: Connecting to a router without
WPS-PBC function
1. Be sure the LAN cable is not connected to
the receiver.
2. Plug the power cord into an AC outlet.
Press STANDBY/ON.
3. Press NET SERVICESETUP.
The Initial Setup screen is shown on the
display.
4. Select Network Setting Network
Confi guration.
5. Useto select Wireless, then press
ENTER.
Network Configuration
Wired
Wireless
6. Useto select Auto, then press
ENTER.
Wireless
Auto
Manual
Wireless Accessory Configuration
Web Control
7. Use to select the available wireless
network you want to connect to, then press
ENTER.
The receiver will only display the names of
2.4 GHz wireless LAN routers (SSID).
4. Press iPod/USB on the remote control.
Connect the iOS device to the USB
terminal.
5. Press SETUP.
6. Select Network Setting Network
Confi guration Wireless iOS Device
and then press ENTER.
7. Tap Allow on iPod/iPhone/iPad.
The Wi-Fi settings of your iPod/iPhone/
iPad are applied to the receiver.
Ignore
Avai
Available Wireless Networks
Availabl
XXXXXXXXX
XXXXXXXX
XXXX
8. Use to enter the Pass Phrase or
WEP Key.
A
[REPEAT]
[CLEAR]
: Moves the adjusting digit.
: Changes displayed character.
REPEAT: Switches character types.
CLEAR: Deletes one character at a time.
9. Use to select DHCP On, then press
ENTER.
Select Don't Use Proxy Server, then
press ENTER.
Network Configuration
DHCP On
DHCP Off
10. In order to activate the setup, press
ENTER .
Refer to Operating Instructions (CD-ROM)
(Connection method 4 | Have the receiver
automatically detect the wireless LAN
router and perform settings on page 33)
and redo the setting again.
© 2014 PIONEER HOME ELECTRONICS CORPORATION.
Share Wi-Fi Settings?
Ignore
lable Wi
e
Wirele
reless N
ss
Netwo
etworks
rks
XXXXX
X
Enter Password
Change Text
Delete One Character
All rights reserved.
5
En