Pioneer VSX-530-K 사용 설명서 - 페이지 33
{카테고리_이름} Pioneer VSX-530-K에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer VSX-530-K 39 페이지. Pioneer vsx-1130-k; vsx-830-k; vsx-530-k av receivers
Pioneer VSX-530-K에 대해서도 마찬가지입니다: 참조 매뉴얼 (27 페이지), 빠른 시작 매뉴얼 (17 페이지), 서비스 매뉴얼 (32 페이지)
페이지 인쇄
Chapter
6
6
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and
malfunctions. If you think that there is something wrong with
this component, check the points below. Take a look at the
other components and electrical appliances being used,
because sometimes the problem may lie there. If the trouble
isn't sorted out even after going through the checks below,
ask your nearest Pioneer authorized independent service
company to carry out repair work.
•
If the unit does not operate normally due to external effects
such as static electricity disconnect the power plug from
the outlet and insert again to return to normal operating
conditions.
General
The power does not turn on.
Disconnect the power plug from the outlet, and insert again.
The receiver suddenly switches off.
When the Auto Power Down function is working, the power will
automatically turn off if the receiver has not operated for
several hours. Check the setting for the Auto Power Down
function (see
The Auto Power Down menu on page
Make sure there are no loose strands of speaker wire touching
the rear panel. This could cause the receiver to shut off
automatically.
After about a minute (you won't be able to switch the unit on
during this time), switch the receiver back on. If the message
persists, call a Pioneer authorized independent service
company.
If there is very little low frequency information in the source
material, change your speaker settings to Front: SMALL /
Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS
The HDMI indicator blinks and the power does not turn
on.
The receiver may have a serious problem. Do not try switching
the receiver on. Unplug the receiver from the wall and call a
Pioneer authorized independent service company.
Power automatically turns ON/OFF and the input switches
from one to another. (When the ARC function is ON)
The CEC (Consumer Electronic Control) function may activate
when the ARC function is turned ON, causing power to turn
ON and OFF and the input to switch from one to another. Since
this unit does not guarantee synchronized operation based on
the CEC function, turn OFF the HDMI CONTROL setting on the
connected player. Refer to the relevant device's instruction
manual for details.
If this does not work, turn OFF the ARC function. If this is the
case, listen to the TV audio after connecting this unit and the
TV with an audio cable.
OVERHEAT shows in the display and the power turns off.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation
Lower the volume level.
TEMP shows in the display and the volume level drops.
The temperature within the unit has exceeded the allowable
value. Try moving the unit for better ventilation
Lower the volume level.
No sound is output when an input function is selected.
Use
to turn up the volume.
VOLUME +/–
Press
MUTE
on the remote control to turn muting off.
Set the
SIGNAL SEL
to H (HDMI), C1/O1 (digital) or A (analog)
according to the type of connections made
Make sure the component is connected correctly (see
Connecting your equipment on page
Check the audio output settings of the source component.
Refer to the instruction manual supplied with the source
component.
31).
No image is output when an input function is selected.
Make sure the component is connected correctly (see
Connecting your equipment on page
Use the same type of video cables for the source component
and TV to connect to this receiver (see
connection on page
14).
The video input selected on the TV monitor is incorrect. Refer
to the instruction manual supplied with the TV.
No sound from subwoofer.
Make sure the subwoofer is switched on.
(page
29).
If the subwoofer has a volume knob, make sure it's turned up.
The Dolby Digital or DTS source you are listening to may not
have an LFE channel.
Switch the subwoofer setting in
YES or PLUS.
Switch the LFE ATT (LFE Attenuate) on
LFEATT 5.
No sound from surround or center speakers.
Connect the speakers properly
Refer to
Speaker Setting on page 29
settings.
Refer to
Channel Level on page 30
No sound from a specific speaker.
Make sure the speaker cable is connected correctly. (Ensure
that the connection terminal is correct, that the speaker wire is
firmly inserted, and that no speaker wire is touching the rear
panel.)
The Phase Control feature doesn't seem to have an
audible effect.
(page
2).
If applicable, check that the lowpass filter switch on your
subwoofer is off, or the lowpass cutoff is set to the highest
frequency setting. If there is a PHASE setting on your
subwoofer, set it to 0º (or depending on the subwoofer, the
setting where you think it has the best overall effect on the
(page
2).
sound).
Make sure the speaker distance setting is correct for all
speakers (see
Considerable noise in radio broadcasts.
Connect the antenna
reception.
(page
19).
Route any loose cables away from the antenna terminals and
wires.
11).
Fully extend the FM wire antenna, position for best reception,
and secure to a wall (or connect an outdoor FM antenna).
Connect an additional internal or external AM antenna
(page
Turn off equipment causing interference or move it away from
the receiver (or move antennas farther away from equipment
11).
causing noise).
Broadcast stations cannot be selected automatically.
About video outputs
Connect an outdoor antenna
Noise during playback of a cassette deck.
Move the cassette deck away from your receiver, until the noise
disappears.
No sound is output or a noise is output when software
with DTS is played back.
Make sure the player's settings are correct and/or the DTS
signal out is on. Refer to the instruction manual supplied with
the DVD player.
Speaker Setting on page 29
to
Can't operate the remote control.
Replace the batteries
page 27
to LFEATT 0 or
Operate within 7 m (23 ft.), 30º of the remote sensor
Remove the obstacle or operate from another position.
Avoid exposing the remote sensor on the front panel to direct
(page
12).
light.
to check the speaker
Press the remote control's
receiver control mode.
to check the speaker levels.
33
Speaker Distance on page
31).
(page
17) and adjust the position for best
17).
(page
17).
(page
10).
button and switch to
RECEIVER
(page
10).