Pioneer VSX-D6025 사용 설명서 - 페이지 32

{카테고리_이름} Pioneer VSX-D6025에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer VSX-D6025 44 페이지.

페이지 인쇄

REMOTE CONTROL OPERATION

The initial functions can operate all products compatible with

PIONEER's common system remote control units marked with the

symbol! ij.

RECEIVER CONTROL BUTTONS

Taras

/par

ona {

—VEe=

Sj 2

64 2

suas.

32cm

caNTem

rae

lonn

zeal; :

> il a

acoveric Ney TY G

; Ty

] 'lcs

RECRIVER

CONTROL

® PIONEER

AUOIO

VIDEO PROGRAMMARLE

REMOTE

CONTROL UNIT

@ RECEIVER POWER button

Switches the receiver power between ON and STANDBY.

@ Input selector buttons

Press when switching the receiver's INPUT SELECTOR.

The CONTROL MODE also switches to the same component (except

VIDEO and PHONO) (One CONTROL MODE button lights).

Pressing TAPE 1/DAT, TAPE 2 MONITOR, causes the CONTROL MODE

DECK II button to light.

@ V. SEL (VIDEO SIGNAL SELECTOR) button

This switches just the video signal in sequence, leaving the sound

unchanged.

VCR 1—+ VCR 2—» LD — TV—+ VIDEO —> of

@ ACOUSTIC select button

The acoustic setting changes in the following manner each time this

button is pressed.

E--D—C-+-B-—A

When playing back a monaural source, press to switch the simulated

stereo function ON/OFF.

The surround mode changes in sequence each time you press this

button.

@ 3CH LOGIC button

Switches DOLBY 3CH LOGIC on and off.

@® CENTER MODE button

When DOLBY PRO LOGIC SURROUND or DOLBY 3CH LOGIC are ON,

use to switch the center mode.

[DOLBY PRO LOGIC SURROUND]

NORMAL — WIDE

PHANTOM Seal

[DOLBY 3CH LOGIC]

NORMAL —+ WIDE Tel

@© EFFECT (+, -) buttons

Effect level can be adjusted when in a surround mode other than DOLBY

PRO LOGIC SURROUND.

DELAY TIME button

During DOLBY PRO LOGIC SURROUND operation, delay time settings

can be changed from 16 ms to 30 ms in 2 ms steps.

The DELAY TIME button does not operate in any other surround mode.

@® AUTO SOURCE CONTROL buttons

@ SLEEP timer button

Activates the SLEEP timer. The length changes in the following

manner each time the button is pressed.

90 —+ 60 — 30 -+ 0 (OFF)

can

Unit: minutes

When SLEEP is ON, the display section is about half as bright as when

SLEEP is OFF.

@ DISPLAY button

Press this for TV screen display.

Does not operate with multivoltage model.

@ RETURN button

Press the RETURN button to return the receiver into the initial state.

TUNER is selected at this initial state. Adjust the sound level by using

the MASTER VOLUME buttons.

OFF

e FUNCTION.............. TUNER

OFF

¢ V-SIGNAL SELECTOR.... OFF

OFF.

° FRONT BALANCE... CENTER

The

HITS

function

searches

for broadcast

stations

among

the

frequencies displayed.

NOTE:

/f no sound is output after the RETURN button is pressed, make sure

that SPEAKERS buttons are turned on.

@ MUTING button

Used to temporarily mute the sound.

The volume is restored when pressed again.

TEST TONE button

Use to adjust the test tone volume level from each speaker.

When the test tone is switched ON, TEST is displayed in the display

section, and the test tone is output through each speaker in turn for

about two seconds. Adjust volume level so that it is the same from each

speaker.

@ MASTER VOLUME (+, -) buttons

Adjusts the overall volume.

LEVEL {-, +)/BALANCE (L, R) buttons and select switch

[Select switch: REAR LEVEL ¢ REAR BAL.)

(-, +)

Adjusts the sound level of the rear speakers to the level of the front

speakers.

{L, R)

Enables balance adjustment of left and right rear speakers.

(-, +)

Adjusts the center speaker sound level.

(L, R)

Enables balance adjustment of left and right front speakers.