Pioneer VSX-D704S 사용 설명서 - 페이지 28

{카테고리_이름} Pioneer VSX-D704S에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer VSX-D704S 40 페이지. Audio/video stereo receiver

페이지 인쇄

OPERATING

USING GUI

I _

Intelligent

Ikj

System Control

GUI

GUI (Graphic User Interface) lets you use the TV screen to

operate the system.

• Press the GUI MODE button on this unit or the G.U.I. button

on the remote control, and operation indications

for the

currently selected function are displayed on the TV screen.

• To operate, use the z_,_>,v,<3buttons on the remote control

(they light up when the GUI mode is ON) or the MULTI-

JOG on this unit to move the cursor (the hand shaped mark)

displayed on the TV screen. When the cursor is on the

button you want to operate, press the GUI ENTER button.

• When the operating

instructions

say "Press the button",

this means move the cursor to the desired button and press

the GUI ENTER button.

NOTE:

• If you do not perform

any of the operations

above

within

10 N 30

seconds, the GUIdisplay is canceled.

• <Multi-voltage model only>

Set the rear panel PAL/NTSC switch to match your TV's color

system. Thescreen will be unclear if the color system does not

match.

RECEIVER CONTROL

BUTTONS

• The buttons in the following

explanation are the receiver operation button indications common to all function displays. (The

illustration shows LD operation indications.)

(Figure 1" Main Menu display)

(Figure 2: Sub Menu display)

®®

1_ SURR MODE (Surround

Mode):

Switches between the five DSP modes and the DOLBY PRO-

LOGIC mode as follows.

DOLBY PRO-LOGIC

JAZZ

DANCE q

SURROUND

ff_

PRO-LOGIC _

HALL _

SIM. SURR ÷

THEATER

(SIMULATED

SURROUND)

The selected mode is displayed on the right of the function

indications.

3CH LOGIC:

Switches DOLBY 3CH LOGIC ON/OFF.

When ON, "3CH LOGIC" is displayed

on the right of the

function indications.

® SUPER BASS:

Swithces SUPER BASS ON/OFF.

When ON, "SUPER BASS" is displayed on the right of the

function indications.

4_ DIRECT:

Press this to listen to source sound without passing the audio

signal through sound quality and balance adjusting circuitry.

The surround

mode, and rear and center

speakers

are

automatically switched off.

COPY:

Press to copy from a Laserdisc to a VCR, or to copy between

VCR 1 and VCR 2.

When you press this button, the display changes to COPY

indications. (This button is displayed only when the function

is LD, VCR 1 or VCR 2. Refer to page 32)

(_ SURR EDIT (Surround

Edit):

Press to make adjustments

such as level setting

for the

currently selected surround mode or DOLB¥ 3CH LOGIC.

When

you press

this

button,

the display

changes

SURROUND EDIT indications. (Refer to page 33)

NOTE:

You cannot press this button when the surround mode is OFF.

SET UP:

Press this button and the display changes to the SET UP

MENU. (Refer to pages 34~36)

Display change button:

Switches

between

Main Menu display (Figure 1) and Sub

Menu display (Figure 2).

® V.SEL (VIDEO SIGNAL SELECTOR):

This switches only the video signal in sequence, leaving the

sound unchanged. (Refer to page 32.)

I--* VCR 1----_VCR 2 --_ VIDEO ---_ TV/SAT--'* LD --I

off

•

SLEEP

This operates the sleep timer. Move the cursor to this button,

and each time you press the GUI ENTER button,

timer

settings change as follows.

90min---_60min----*30min-_*0min

(off)--I

@ SYSTEM

OFF

Switches power to this unit, the TV, and the currently selected

function OFF.

NOTE:

When you press the SYSTEM OFF button, power to components

not made by Pioneer switches ON if power to these components

was alreadyswitched OFF.