Pioneer A-509R 서비스 매뉴얼 - 페이지 27

{카테고리_이름} Pioneer A-509R에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer A-509R 30 페이지.
Pioneer A-509R에 대해서도 마찬가지입니다: 사용 설명서 (12 페이지)

페이지 인쇄

REC SELECTOR switch /indicator(For TAPE 1/CD-

R/MD terminals)

This switch is used to select the recording source component.

The signal from the selected component is output at the TAPE1/

CD-R/MD jacks for recording. To select a recording source com-

ponent, press the REC SELECTOR switch so that the indicator

of the desired source component lights up. When this switch is

set to [TUNER] or [CD], the signal from the selected component

can be recorded regardless of the input selector switch and

TAPE2 MONITOR button settings.

: To record from the equipment connected to the CD

terminals.

TUNER : To record from the equipment connected to the

TUNER terminals.

SOURCE : To record from the equipment selected by the IN-

PUT SELECTOR knob.

OFF

: In this position, nothing from the REC terminals of

TAPE 1/CD-R/MD is output. Set to this position when

not recording; the cassette deck will be disconnected,

improving sound quality.

NOTE:

The function selected using the INPUT SELECTOR knob will be

recorded irrespective of the position of the REC SELECTOR

switch (TAPE 2 MONITOR terminals).

BALANCE control

Should normally be left in the center position. Adjust the balance

if the sound is louder from one of the speakers. If the right side is

louder, turn toward the L (left) position and if the left side is louder,

turn toward the R (right) position.

NOTE:

This control does not operate at DIRECT ON mode.

DIRECT/SB MODE button/indicator

Press and hold the button for more than 3 seconds to switch SB

mode ON. (Volume indicator goes out)

Press and hold the button for more than 3 seconds again to

switch SB mode OFF. (Volume indicator lights)

[DIRECT]

Use this button when you do not wish to pass the output from

input terminal equipment through the various frequency adjust-

ing circuits (BASS, TREBLE, BALANCE, LOUDNESS).

On : The indicator lights. The signals input through the input

terminals are reproduced without passing through the

various frequency adjusting circuits. This results in flat,

pure sound which is a more faithful reproduction of the

input source.

Off : The indicator goes out. The signal passes through the

various frequency adjusting circuits.

[SB MODE]

The SB mode is a special mode in which the amplifier does not

accept remote control except power ON/OFF (But all of the fa-

cilities can be controled by manual as same as SB mode OFF.).

Fix the VOLUME control near the center position.In this mode,

the set can be used as a power amplifier which amplifies the

LINE/SURROUND BACK input (the function name is LINE/SB)

with a input sensitivity of 1V.

For example, when the set is combined with one of Pioneer's

Surround Back compatible receiver, the set can be used sa the

Surround Back amplifier.

(For details, please refer to the instruction manual of the receiver.)

LOUDNESS button/indicator

Use when listening at low volume level.

On : The indicator lights. Boosts low and high frequencies to

give added punch to playback even at low volume level.

Off : The indicator goes out. Should normally be left in this

position.

NOTE:

This button does not operate at DIRECT ON mode.

TREBLE tone control

Use to adjust the high-frequency tone. The center position is the

flat (normal) position. When turned to the right, the high-frequency

tone is emphasized; when turned to the left, the high-frequency

tone is de-emphasized.

NOTE:

This control does not operate at DIRECT ON mode.

BASS tone control

Use to adjust the low-frequency tone. The center position is the

flat (normal) position. When turned to the right, the low-frequency

tone is emphasized; when turned to the left, the low-frequency

tone is de-emphasized.

NOTE:

This control does not operate at DIRECT ON mode.

PHONES jack

When using headphones, insert the plug into this jack.

SPEAKERS B (ON/OFF) button/indicator

Use this button to listen to the speaker system connected to the

SPEAKERS B terminals.

On : The indicator lights. Sound is heard from the speaker sys-

tem.

Off : The indicator goes out. No sound is heard from the

speaker system. Set to this position when listening with

headphones.

SPEAKERS A (ON/OFF) button/indicator

Use this button to listen to the speaker system connected to the

SPEAKERS A terminals.

On : The indicator lights. Sound is heard from the speaker sys-

tem.

Off : The indicator goes out. No sound is heard from the

speaker system. Set to this position when listening with

headphones.

A-509R