Pioneer Elite M-10X 사용 설명서 - 페이지 8

{카테고리_이름} Pioneer Elite M-10X에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer Elite M-10X 36 페이지. Operating instructions
Pioneer Elite M-10X에 대해서도 마찬가지입니다: 사양 시트 (1 페이지), 사용 설명서 (12 페이지), 서비스 매뉴얼 (22 페이지)

페이지 인쇄

TROUBLESHOOTING

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong

with this component, check the points below. Sometimes the trouble may lie in another component. Investigate

the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising

the checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair

work.

Symptom

No power is supplied

to unit.

No sound.

Abnormal functioning of this unit may be caused by static electricity, or other external interference. To restore

normal operation, turn the power off and then on again, or unplug the AC power cord and then plug it in again.

SPECIFICATIONS

Amplifier Section

Continuous power output

(both channels driven at 20 Hz to 20 kHz)*

T.H.D. 0.09 %, 4

T.H.D. 0.05 %, 8

DIN Continuous power output (both channels driven at

1 kHz)

T.H.D. 1.0 %, 4

T.H.D. 1.0 %, 8

Total harmonic distortion*

20 Hz to 20 kHz, 8

•

Power output specification is for when power sup-

ply is 230V.

Input sensitivity/ impedance ................ 700 mV/ 50 k

Frequency response .................. 5 Hz to 100 kHz

Signal-to-Noise ratio (IHF A network, short circuit)

....................................................................... 118 dB

En/Ge

Cause

• Power plug is disconnected from inlet and outlet.

• The amplifier's power plug has been plugged

into another component's power outlet (e.g.

timer, etc.) but power to that unit is discon-

nected.

•

STANDBY/ON button is set to STANDBY.

• MAIN POWER( —OFF/_ON ) button is set to

OFF.

• Connecting cords are disconnected from

terminals.

• Cords are connected incorrectly.

• Terminals or connecting cords pin plugs are

dirty.

• Operation of other components is incorrect.

For example:

In an A/V receiver the speaker settings are

incorrect, the input selector is set incorrectly,

the output settings are incorrect, or the

volume is turned all the way down.

In a DVD player the sound settings are in-

correct, etc.

• The disc you are using has no sound on these

channels.

.............................. 90 W + 90 W

.............................. 60 W + 60 W

............................ 120 W + 120 W

................................ 75 W + 75 W

..................................... 0.05 %

Power Supply/ Miscellaneous

Power requirements ..... AC 220 – 230 Volts, 50/ 60 Hz

Power consumption ............................................ 220 W

Power Consumption in standby mode .................. 1 W

Dimensions ................ 420 (W)

(including knobs and other protruding parts)

Weight (without package) ................................... 7.6 kg

Accessories

Operating instructions ................................................. 1

Power cord (Rated current 2.5 A) ................................ 1

Remote control cord .................................................... 1

Warranty card ............................................................... 1

NOTE:

Specifications and design subject to possible modification without

notice, due to improvements.

–3

Measured by Audio Spectrum Analyzer.

Remedy

• Insert plug securely into inlet and

outlet.

• Turn on power to other compo-

nent.

• Press the

STANDBY/ON button

to ON so that the STANDBY

indicator goes off.

• Set the MAIN POWER (—OFF/

_ON ) button to ON.

• Connect securely.

• Connect correctly. (See page 5)

• Clean terminals and plugs.

• Consult the operating instructions

for the other components.

• Check the format of the disc you

are using.

319 (D)

Published by Pioneer Corporation.

128 (H) mm