Pioneer GM-4000F 소유자 매뉴얼 - 페이지 3

{카테고리_이름} Pioneer GM-4000F에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer GM-4000F 8 페이지. Bridgeable four-channel power amplifier
Pioneer GM-4000F에 대해서도 마찬가지입니다: 소유자 매뉴얼 (6 페이지)

페이지 인쇄
Pioneer GM-4000F 소유자 매뉴얼
Connecting the Unit

Connecting the Power Terminal

4. Connect the wires to the terminal.
• Fix the wires securely with the terminal
• Always use the special red battery and ground
screws.
wire [RD-223], which is sold separately. Connect
the battery wire directly to the car battery positive
GND terminal
terminal (+) and the ground wire to the car body.
Power terminal
System remote
control terminal
1. Pass the battery wire from the
engine compartment to the interior
System remote
of the vehicle.
control wire
• After making all other connections to the
amplifier, connect the battery wire terminal of
the amplifier to the positive (+) terminal of
the battery.
Engine
Fuse (30 A)
compart-
Interior of
ment
the vehicle
Battery wire
Fuse (30 A)
Drill a 14 mm
Connecting the Speaker Output
Positive terminal
(1/2 inch) hole
Terminals
Insert the O-ring rubber
into the vehicle
grommet into the vehicle
body.
body.
1. Expose the end of the speaker wires
using nippers or a cutter by about
10 mm (3/8 inch) and twist.
2. Twist the battery wire, ground wire
and system remote control wire.
Twist
10 mm
(3/8 inch)
2. Attach lugs to speaker wire ends.
Lugs not supplied.
3. Attach lugs to wire ends. Lugs not
• Use pliers, etc., to crimp lugs to wires.
supplied.
Lug
• Use pliers, etc., to crimp lugs to wires.
Lug
Speaker wire
Ground wire
Lug
Battery wire
3. Connect the speaker wires to the

Using the Speaker Input

speaker output terminals.
Connect the car stereo speaker output
• Fix the speaker wires securely with the termi-
wires to the amplifier using the supplied
nal screws.
speaker input connector.
• Do not connect both the RCA input and the
Terminal screw
speaker input at the same time.
7 Connections when using the speaker
input
Ground wire
Speaker
output
terminal
Speaker wire
Twist
Speaker input connector
To speaker input terminal of
this unit.

Connecting the Speaker wires

The speaker output mode can be four-channel, three-channel (stereo +
mono) or two-channel (stereo, mono). Connect the speaker leads to suit the
mode according to the figures shown below.
• When either the RCA input or the speaker input is connected, RCA output
becomes functional. Do not connect both the RCA input and the speaker input at
the same time.
Four-channel mode
Input Select Switch
For two-channel input, slide this switch to
the left. For four-channel input, slide this
Car Stereo
switch to the right.
Speaker input
Speaker input
terminal A
terminal B
Speaker output
Speaker input
connector
White/black:
Gray/black:
Left ≠
Right ≠
White:
Gray:
Left +
Right +
Three-channel mode
Input Select Switch
For two-channel input, slide this switch to
the left. For four-channel input, slide this
switch to the right.
Speaker input
Speaker input
terminal A
terminal B
Speaker input
connector
Two-channel mode (stereo)
Input Select Switch
Slide this switch to the left.
Speaker input
terminal A
(Left)
Speaker out A
(Right)
Speaker input
connector
+
≠
≠
+
Speaker output
terminal
Two-channel mode (mono)
+
≠
≠
+
(Right)
Speaker out B
Input Select Switch
(Left)
Slide this switch to the left.
Speaker input
terminal A
(Left)
Speaker input
Speaker out A
connector
(Right)
+
≠
≠
+
Speaker output
terminal
≠
+
Speaker out B
(Mono)
Speaker (Left)
+
≠
Speaker output
terminal
≠
+
Speaker (Right)
Speaker (Mono)
+
≠
Speaker output
terminal
≠
+
Speaker (Mono)