Pioneer PD-M427 사용 설명서 - 페이지 12

{카테고리_이름} Pioneer PD-M427에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer PD-M427 40 페이지. Multi compact disc player
Pioneer PD-M427에 대해서도 마찬가지입니다: 사용 설명서 (28 페이지), 서비스 매뉴얼 (32 페이지), 서비스 매뉴얼 (32 페이지), 서비스 매뉴얼 (32 페이지), 사용 설명서 (40 페이지)

Pioneer PD-M427 사용 설명서
TO PLAY ONLY DESIRED TRACKS/DISCS
Direct Program:
During normal playback or Magazine Hi-Lite Scan playback,
the track being played can be programmed.
1. Press the PROGRAM button to enter the program
mode.
2. To search for a desired track during normal play
back, it is possible to skip to succeeding tracks by
pressing the 4 1 or ¡ ¢ button.
Also, Magazine Hi-Lite Scan function can be used to move
from track to track through the disc.
3. If you wish to program the track currently playing,
press the PROGRAM button while the track is
playing.
÷ Direct programming is not possible during program
playback.
To check the program contents (PD-M427 only) :
During program mode, set the player to stop mode and press
the CHECK button on the remote control unit. The program
contents will be displayed in the programmed order.
÷ After confirming the last program step, the display will
show "0-00".
PROGRAMMING A PAUSE (PD-M427 only)
Inserting a pause in your program can be very useful when
carrying out recording. Press the 8 button on the remote
control unit instead of entering a track number. "PA" appears
on the display panel.
÷ For example, when recording on both sides of a cassette
tape, if you program a pause after the last track to be
recorded on the first side, program playback will pause at
that point to allow you to switch tape sides. To resume
program playback after the player enters pause mode,
press the 8 button on the remote control unit or 6
button on the front panel.
NOTES:
÷ A pause can be programmed only when the program
procedure is performed under stop mode.
÷ A pause cannot be programmed at the beginning of a
program (P–01), nor can two pauses be programmed one
after the other
÷ A pause inserted in a program is counted as one step.
÷ If a pause is programmed as the last step of a program, the
player will not enter the pause mode.
12
En
To erase a program (PD-M427 only) :
During program mode, press the CLEAR button on the
remote control unit.
The last program step is erased and the contents of the
previous program step are displayed.
NOTE:
Contents of a program can be erased during playback as well.
However tracks preceding the currently playing track cannot
be erased in this way.
To clear all of the program contents:
A. During stop mode, press the 7 button.
B. When the magazine is ejected, the program contents will
be cleared.
To modify the program contents (PD-M427 only) :
1. During program mode, set the player to stop
mode and press the CHECK button on the remote
control unit so that the program step to be
corrected appears on the display.
2. Enter the new disc number with the DISC
NUMBER (DISC 1-DISC 6) buttons and then press
the 4 1 or ¡ ¢ button so that the new
track number appears on the display.
3. Press the PROGRAM button.
÷ Repeat steps 1 through 3 to change other tracks as
desired.
÷ If the 4 1 or ¡ ¢ button is not pressed within
2 seconds when correcting the track number, the
displayed track number is automatically memorized.