Pioneer VSA-E03 사용 설명서 - 페이지 24

{카테고리_이름} Pioneer VSA-E03에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer VSA-E03 48 페이지. Audio/video multichannel amplifier

페이지 인쇄

Names of Parts and Basic Operations

Front Panel

2 3

AUDIO/VIDEO MUL TI-CHANNEL AMPLIFIER

ST ANDBY

ST ANDBY/ON

CHANNEL

–

LEVEL

–

OFF

PHONES

1 Main power switch (— OFF, _ ON)

STANDBY/ON button

Press to switch the amplifier on or put in standby.

3 STANDBY indicator

Lights when the amplifier is in standby mode. (Please

note that this amplifier consumes a small amount of

power (2 W) during the standby mode.)

4 CHANNEL SELECT button

Use to select a speaker when ajusting speaker levels.

5 SPEAKERS (A/B) buttons

Use to switch the corresponding speaker system on

or off. To listen to both speaker systems (A and B),

press the buttons so that both A and B appear in the

display (refer to "Display", 0, Speaker indicators on

page 22). Only A speakers are available when using

surround sound modes.

6 BASS (–/+) button

Press to adjust low frequencies in the range of ±6.

7 Display (Refer to page 22)

8 TREBLE (–/+) button

Used to adjust high frequencies in the range of ±6.

9 LOUDNESS button

Switches the loudness on or off. Use to raise the level

of the bass and treble so they can be more easily

heard when listening at low volumes.

0 Remote sensor

Point the remote control toward the remote sensor to

operate the amplifier.

4 5

N∫z¿x?≤

CHANNEL

SELECT

SPEAKERS

B ASS

–

VCR

D VD/LD

TV/SA T

VIDEO

D VD 5.1CH

9 0 - = ~ !

MODE

SIGNAL

SELECT

MIDNIGHT

TREBLE

–

LOUDNESS

DIRECT

TUNER

MD/T APE

A UX

(Dolby) Surround button

Press to select the

mode automatically switches between Dolby Digital

and Dolby Pro Logic decoding according to the input

signal. (Refer to page 29 for more information about

Dolby Digital.)

= SIGNAL SELECT button

Use to select input signals for the digital components.

First press VCR, DVD/LD, TV/SAT, CD or MD/TAPE (%,

Function buttons) to select the component, then press

SIGNAL SELECT repeatedly to select one of the

following:

ANALOG : Selects the analog (R and L) audio signals.

DIGITAL : Selects the digital audio signals. This

amplifier automatically detects and displays the

format of the signal being input. AC-3 lights when

Dolby Digital signals are input. (AC-3 decoding is

switched automatically.)

• SIGNAL SELECT is fixed in the "ANALOG" position

for components not assigned to one of the three

digital input jacks.

• Because the audio from a karaoke microphone and

LD recorded with analog audio only is not output

from the digital output, set SIGNAL SELECT to

"ANALOG".

• This amplifier can only play back Dolby Digital,

PCM (32kHz, 44kHz, and 48kHz) signal formats. With

digital signal formats other than these, set SIGNAL

SELECT to "ANALOG".

~ DSP MODE button

Press repeatedly to select a DSP sound mode (HALL 1,

HALL 2, JAZZ, DANCE, THEATER 1, or THEATER 2).

Use these modes to produce surround sound from

standard (two channel) stereo sources (refer to page

26, 30).

MASTER

V OLUME

DSP

DO WN

VIDEO INPUT

VIDEO

A UDIO R

S-VIDEO

(Dolby) Surround mode. This