Pioneer CDJ-800 사용 설명서 - 페이지 14

{카테고리_이름} Pioneer CDJ-800에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer CDJ-800 20 페이지. Correction
Pioneer CDJ-800에 대해서도 마찬가지입니다: 문서 업데이트 (4 페이지)

페이지 인쇄

1. Connections

BASIC OPERATION: DJ PLAYER OPERATION

÷ When the DJ Mixer's CROSS FADER slider has moved all the way to the

right side, the sound heard from the speaker will have changed from track

A to track B, and the operation is complete.

7 Long mix play

If the BPM rates match, mixing of tracks A and B will sound good even if the

CROSS FADER slider is in the middle position.

ADVANCED OPERATIONS

RELOOP/EXIT

QUICK RETURN

LOOP OUT

(OUT ADJUST)

AUTO BEAT

LOOP 1,2,4,8

LOOP IN

REALTIME

CUE

REV

1, ¡

CUE

PLAY/PAUSE

Jog dial

Scratch Play (*)

By changing from the JOG MODE to VINYL, and pressing and rotating the surface

of the Jog dial you can replay according to the speed and direction of the Jog dial.

1. Press the JOG MODE VINYL button so the button

indicator lights.

÷ The Jog dial's [Vinyl] indicator also lights.

2. When replaying a CD press the surface of the Jog dial.

÷ Playback slows down and stops (the slowdown in speed until the disc stops

(response characteristics) can be set separately). By rotating the Jog dial

when playback speed is decreasing but not yet stopped all sound will stop

halfway through. See Step 3 for playback when rotating the Jog dial.

3. Turn the Jog dial in the direction and at the speed you

wish to playback the disc.

÷ The CD is played back according to the speed and direction of Jog dial

movement.

4. Take your hand off the surface of the Jog dial.

÷ The CD spins up or down to return to normal playback mode.

(The slowdown or increase in speed until the CD returns to normal play-

back (response characteristics) can be set separately.)

7 This function sets the time to full stop when the Jog

dial's surface is pressed, and the time from full stop to

normal playback speed when the surface of the Jog dial

is released.

Rotate the VINYL SPEED ADJUST TOUCH/RELEASE dial.

÷ Rotating the dial changes the deceleration speed (response) from playback

to full stop, and the acceleration speed (response) from full stop to normal

playback.

How to Spin (*)

During playback in the VINYL mode either press the surface of the Jog dial or press the

PLAY/PAUSE button (6) to cause a pause, then quickly turn the Jog dial, even

when released playback will occur according to the speed and direction of the dial.

JOG MODE VINYL

VINYL SPEED ADJUST

TOUCH/RELEASE

7 Fader start play

Using the cross fader start function of the DJM-600, DJM-500, DJM-300 or DJM-

3000 step 10 above can be eliminated for even simpler mixing. In addition,

when the CROSS FADER slider is returned to its original position, the status

returns to that in step 9 (player CD2 at its Cue point), so that you can repeat the

same play as many times as you like.

Functions indicated with an asterisk (*) are disabled when

the rear panel DIGITAL OUT MODE switch is set to NORMAL.

How to Brake (*)

÷ When you press the PLAY/PAUSE button (3/8)in the VINYL mode dur-

ing playback, the VINYL SPEED ADJUST TOUCH/RELEASE dial will

cause a corresponding speed and the sound will stop.

÷ Upon pressing the PLAY/PAUSE button (3/8) again playback will com-

mence and the VINYL SPEED ADJUST TOUCH/RELEASE dial will

respond accordingly.

Quick Return (*)

When the JOG MODE is set to VINYL, pressing the surface of the Jog dial returns

playback instantly to the cue point.

1. Press the JOG MODE VINYL button so that the button

indicator lights.

÷ The Jog dial's [Vinyl] indicator also lights.

2. Press the QUICK RETURN button so that the button

indicator lights.

÷ The [QUICK RETURN] indicator will appear in the display, and the Jog

dial display will shown the flashing cue point position indicator.

3. During playback, press the surface of the Jog dial.

÷ If a cue point has been stored in memory, the playback will return instantly

to the stored cue point; if no cue point has been stored in memory, the

playback will not change.

÷ Playback will also return to the in-point (cue point) if the Jog dial is pressed

during loop playback.

Loop Playback (*)

7 Defining a loop (MANUAL)

1. Press the PLAY/PAUSE button (6) to begin playback.

2. During replay, press the LOOP IN/REALTIME CUE button

at the loop in point.

÷ Note that this operation need not be performed if a prerecorded Cue point is

to be used as the start of the loop.

3. During playback, press the LOOP OUT button at the point

from which you wish to end the loop.

÷ The AUTO BEAT LOOP 8 (MANUAL 1/1) button indicator lights.

÷ Loop play begins between the loop in-point to loop-out point.

7 Shorten the Loop Length (LOOP CUTTER)

When MANUAL mode is used to create a loop during playback or pause, the

AUTO BEAT LOOP 8 (MANUAL 1/1) button will light.

Press one of the AUTO BEAT LOOP buttons (1, 2, 4 or 8).

÷ When the AUTO BEAT LOOP 1 (MANUAL 1/8) button is pressed, the

button indicator lights and loop play begins between the loop-in point to a

point 1/8 of the full length of the original loop.

÷ When the AUTO BEAT LOOP 2 (MANUAL 1/4) button is pressed, the

button indicator lights, and loop play begins between the loop-in point to a

point 1/4 of the full length of the original loop.

÷ When the AUTO BEAT LOOP 4 (MANUAL 1/2) button is pressed, the

button indicator lights, and loop play begins between the loop-in point to a

point 1/2 of the full length of the original loop.

÷ When the AUTO BEAT LOOP 8 (MANUAL 1/1) button is pressed, the

button indicator lights, and loop play begins between the loop-in point to a

point 1/1 (all) of the length of the original loop.