Pioneer CMX-3000 사용 설명서 - 페이지 32

{카테고리_이름} Pioneer CMX-3000에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer CMX-3000 33 페이지. Owner's manual
Pioneer CMX-3000에 대해서도 마찬가지입니다: 사용 설명서 (20 페이지)

페이지 인쇄

Appendix

TROUBLESHOOTING

If you believe your CD player is failing to work properly, check the following troubleshooting table for tips. Sometimes simple mistakes in setup or

operation may appear like serious problems. There are also times when the problem in question may be caused by something else other than your CD

player, and at times like these you should check any other electronic devices being used at the same time.

If the problem in question continues to persist even after checking the troubleshooting table below and taking whatever corrective action is

recommended, contact your nearest Pioneer Service Station or contact the store from which you purchased your player for further assistance.

Description of problem

A disc fails to be ejected even after the

EJECT button (0) has been pressed.

Playback doesn't begin even when a

disc is inserted.

Playback comes to a halt almost

immediately after it begins.

No sound is output.

Sound is distorted or full of noise.

A large amount of noise is generated

when playing back a certain disc or

discs. Playback halts unexpectedly.

Track searching fails to halt with Auto

Cue function turned ON.

The jog dial doesn't work.

The jog dial performs a different

function from that desired.

Back cueing fails to work when the

CUE button is pressed during playback.

Unable to produce loop playback by

pressing the LOOP OUT/OUT ADJ but-

ton.

Unable to perform DJ operations

Auto cue and other settings are not

stored.

WAVE data is not stored.

HOT CUE data is not stored.

Television pictures are distorted or

noise appears in FM broadcasts.

Disc is not rotating even though power

has been turned on.

En/Sp

Possible cause of problem

÷ Power cord has not been plugged in.

÷ A track is being played back.

÷ EJECT button (0) is broken.

÷ Auto Cue function is turned ON.

÷ Disc has been inserted upside down.

÷ Disc is dirty or covered with condensation.

÷ Audio cable has come loose or has not been

properly plugged in.

÷ DJ mixer is not working properly.

÷ Jacks or jack plugs are dirty.

÷ Player is currently in pause mode.

÷ Audio cable has not been properly plugged in.

÷ Jacks or jack plugs are dirty.

÷ Player is subject to noise from a nearby television

set.

÷ Disc is seriously warped or scratched.

÷ Disc is unusually dusty or dirty.

÷ Track searching sometimes takes longer than

expected when the length of silent portions

between tracks is unusually long.

÷ If the length of a silent portion between two tracks

is longer than 10 seconds in duration, the second

track cannot be played back unless Auto Cue

function is turned OFF.

÷ The DIGITAL MODE switch is set to ON.

÷ The jog mode is incorrect.

÷ No cueing point has been defined.

÷ The DIGITAL MODE switch is set to ON.

÷ No cueing point (i.e., starting point) has been

defined.

÷ The DIGITAL MODE switch is set to ON.

÷ The power was turned off right after a setting was

made.

÷ The data is stored when playback of the current

track is completed.

÷ The HOT CUE data is stored in memory when the

disc is ejected.

÷ Interference caused by CD player.

÷ Disc rotation is automatically halted when no

operation is performed for 80 minutes or longer

when in pause mode.

÷ When the last track on the disc is over the disc

stops rotating.

Recommended action

÷ Plug in power cord.

÷ Set the player to pause or cue standby mode

before pressing the EJECT button (0).

÷ See p. 8.

÷ Press the PLAY/PAUSE button (38) to begin

play.

÷ Hold the TIME MODE/AUTO CUE button

depressed for 1 second or more to set the

Auto Cue mode to OFF.

÷ Reinsert with label side facing upward.

÷ Wipe disc to remove dust or condensation.

÷ Plug in audio cable properly.

÷ Check switch and volume settings on DJ

mixer.

÷ Wipe away dust or dirt and reinsert plugs.

÷ Press the PLAY/PAUSE button (38) to begin

play.

÷ Connect audio cable to line input jack of DJ

mixer. Do not connect to microphone jack.

÷ Wipe away dust or dirt and reinsert plugs.

÷ Turn off power to television set or move

television set further away from CD player.

÷ Replace with new disc.

÷ Wipe away dust or dirt from disc.

÷ Hold the TIME MODE/AUTO CUE button

depressed for 1 second or more to set the

Auto Cue mode to OFF.

÷ Set the DIGITAL MODE switch to OFF.

÷ Press the JOG MODE button to select the

desired function.

÷ Specify the desired cueing point. (See p. 21.)

÷ Set the DIGITAL MODE switch to OFF.

÷ Specify the desired cueing point. (See p. 21.)

÷ Set the DIGITAL MODE switch to OFF.

÷ Wait 10 seconds before turning off the

power after a change.

÷ Wait until playback of the current track is

completed.

÷ Eject the disc. (Then turn off the power.)

÷ Turn off the power to the CD player or move

the player further away from the radio or

television set.

÷ Press the PLAY/PAUSE button (38) to begin

playback. Alternatively, press the EJECT

button (0) to eject the disc.