Pioneer DEH-P7700MP - In-Dash CD/MP3/WMA/WAV/iTunes AAC Car Stereo Receiver 설치 매뉴얼 - 페이지 2

{카테고리_이름} Pioneer DEH-P7700MP - In-Dash CD/MP3/WMA/WAV/iTunes AAC Car Stereo Receiver에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer DEH-P7700MP - In-Dash CD/MP3/WMA/WAV/iTunes AAC Car Stereo Receiver 6 페이지. Multi-cd control high power cd/mp3/wma player with fm/am tuner
Pioneer DEH-P7700MP - In-Dash CD/MP3/WMA/WAV/iTunes AAC Car Stereo Receiver에 대해서도 마찬가지입니다: 설치 매뉴얼 (6 페이지), 소유자 매뉴얼 (34 페이지), 설치 매뉴얼 (9 페이지), 운영 매뉴얼 (4 페이지), 서비스 매뉴얼 (21 페이지), 서비스 매뉴얼 (20 페이지)

Pioneer DEH-P7700MP - In-Dash CD/MP3/WMA/WAV/iTunes AAC Car Stereo Receiver 설치 매뉴얼

Installation

ENGLISH
2. Install the microphone clip on the

Adjusting the microphone angle

steering column.
The microphone angle can be adjusted by
moving forward or backward the micro-
Double-sided tape
phone clip angle.
Install the microphone clip on the rear side
of the steering column.
Clamps
Use clamps to
secure the lead
where necessary
inside the vehicle.

Connecting the Units

ENGLISH
Note:
Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
external power amp's system remote control or
red cable must be wired to the terminal that can
the vehicle's auto-antenna relay control terminal
detect the operation of the ignition key.
(max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
Otherwise, battery drain may result.
antenna booster power supply terminal.
Never connect blue/white cable to external power
amp's power terminal. Also, never connect it to
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
Black cable is ground. This cable and other prod-
ACC position
No ACC position
uct's ground cable (especially, high-current prod-
Use this unit in other than the following condi-
ucts such as power amp) must be wired separate-
tions could result in fire or malfunction.
ly. Otherwise, fire or malfunction may result if
— Vehicles with a 12-volt battery and negative
they are accidentally detached.
grounding.
Cord function may differ according to the
— Speakers with 50 W (output value) and 4 ohm
product, even if cord color is the same. When
to 8 ohm (impedance value).
connecting this system, be sure to check all
To prevent short-circuit, overheating or malfunc-
manuals and connect cords correctly.
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the battery
before installation.
— Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhesive
tape around them where they lie against metal
parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not remove RCA caps if RCA cables are
not used.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's nega-
tive cables.