Pioneer PD-41 사용 설명서 - 페이지 10

{카테고리_이름} Pioneer PD-41에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer PD-41 28 페이지.
Pioneer PD-41에 대해서도 마찬가지입니다: 서비스 매뉴얼 (42 페이지)

페이지 인쇄

CONNECTIONS

Output cable

BALANCED INPUT

Put these parts together

when inserting the

connector.

When removing,

push on the

protruding part.

Control amplifier

Power cord

CD-DECK

Amplifier

~ Control cord

e@ Make sure that all of the components are turned off before

making connections.

Analog output connections

When using the LINE OUT jacks (pin-jack)

_ Connect the OUTPUT jacks of this unit to the input jacks (CD or AUX)

of the amplifier. Make sure that the white plugs are connected to the

left (L) jacks and the red plugs to the right (R) jacks.

Be sure not to connect this unit to the amplifier's PHONO

jacks, as sound will be distorted and normal playback will not

be possible.

When using the BALANCED LINE OUT jacks (U.S. and

Canadian models of PD-75 only):

Connect the BALANCED LINE OUT jacks of this unit to a control

amplifier equipped with the balanced input jacks. The same channels

of this unit and the control amplifier should be connected properly;

right to right, and left to left. Connecting the balanced output protects

against the undesirable effects of external noise and induction to

provide even higher sound quality, andis

thus the preferred connection

method

for professiona! applications such as studio use and

broadcasting. Use a commercially-available Cannon connector (XLR-

3-32 or equivalent).

Connecting to the digital jack

This unit can be connected to an amplifier equipped with an optical

digital jack or coaxial digital jack.

.When using the OPTICAL DIGITAL OUT jack:

1. ae

the protective dust cap from this unit's OPTICAL DIGITAL

UT jack.

2. Use an optical fiber cable to connect the OPTICAL DIGITAL OUT

jack of this unit to the optical digital input jack of the amplifier.

Align the plug of the optical fiber cable with the optical digital jack

and fully insert the plug to make a secure connection.

Use a

separately sold optical fiber cable for the optical digital jack

connections.

NOTES:

e@ When. making optical digital connections, this player can only be

connected to an amplifier which uses the same type of optical

transmission/reception module.

@ Fully insert the optical fiber cable plugs all the way into the jacks.

@ Be careful not to fold or crimp the cable. When coiling an optical

fiber cable for storage, make sure the diameter of the coilis 15cm

(6 in) or lager.

Use an optical fiber cable with a length of 3 m (9 ft) or less.

Protect the optical fiber cable plugs from scratches and dust.

When the unitis not connected using an optical fiber cable, be sure

to keep the protective dust cap plugged into the optical digital

output jack at all times.

SYNCHRO cord

Cassette deck

When using the COAXIAL DIGITAL OUT jack:

;

Use a coaxial digital cable to connect the COAXIAL DIGITAL OUT jack

of this unit to the coaxial digital input jack of the amplifier.

CD-Deck synchro function

If you have a Pioneer cassette deck provided with the CD-Deck

synchro function, connect the CDeDECK SYNCHRO jacks of the

CD player and cassette deck. With this function, synchro recording

can be carried out between player and deck.

@ For details on connections and operation, refer to the instruction

manual supplied with the cassette deck.

e@ The CD-DECK SYNCHRO cord is not supplied with the CD player.

NOTES:

When only the digital output is connected, the CD-Deck synchro

recording does not function. To operate it, connect the output cable to

the stereo amplifier as well as connecting the digital output.

System remote control with a Pioneer stereo

'amplifier that has the fj] mark (U.S. and

Canadian models only)

When a Pioneer stereo amplifier bearing the fj] mark is used,

connect the CONTROL IN jack on the rear panel of the CD player

to the CONTROL OUT jack of the amplifier.

This will enable the

CD player to be controlled using the remote control unit supplied

with the stereo amplifier.

If you do not plan to use this feature, it

is not necessary to connect CONTROL IN/OUT jacks.

e The control cord is supplied with the CD player.

@ The remote control unit supplied with the amplifier can be used

to control Play, Stop, Pause and Track Search.

For instructions regarding connections and operation, refer to

the operating instruction

manual

provided with your stereo

amplifier.

NOTES:

Be sure to connect both of the controf cord's plugs securely to

the CONTROL IN and CONTROL OUT terminals. Do not connect

only one end of the cable.

;

Be sure to turn off the power of the amplifier when connecting

the power cord and output cord.

When only the digital output is connected, the remote sensor of

the amplifier does not function. To operate it, connect the output

-cable to the stereo amplifier as well as connecting the digital

output.

Power cord connection