Pioneer PDR-509 사용 설명서 - 페이지 37

{카테고리_이름} Pioneer PDR-509에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer PDR-509 40 페이지. Compact disc recorder
Pioneer PDR-509에 대해서도 마찬가지입니다: 서비스 회로도 (23 페이지), 서비스 매뉴얼 (48 페이지), 서비스 매뉴얼 (23 페이지), 서비스 매뉴얼 (14 페이지)

페이지 인쇄

Troubleshooting

Below is a list of messages mainly related to playback and recording problems, together with a brief explanation and a page

reference where you can find more information:

Display

Cause

CHECK DISC

The disc is damaged or dirty.

The disc is loaded upside down.

CHECK

A system error occurred, perhaps due

(blinking

to noise or static electricity.

display)

Display messages relating to recording:

Display

Cause

CAN NOT

The input signal is digital-copy pro-

COPY

tected with

CAN NOT REC

The digital source was interrupted.

The source is not audio, or is an

incompatible format (e.g. a

CHECK INPUT

The source player was already playing

(CD) ?

when the

pressed.

SET UP

The unit is preparing to record.

REPAIR

The recorder was switched off/

unplugged after recording without

ejecting the disc. The recorder could

not write essential recording informa-

tion onto the disc.

RESUME

The unit is resuming an operation. If

the power supply is cut off (either by

mistake or due to a power failure)

during recording, the unit enters

resume mode once power is restored

so that additional recording is possible.

REC FULL

No more recording is possible because

the available recording time of the disc

has been used up, or 99 tracks have

already been recorded on the disc.

Pro DISC

The loaded disc is a

disc for professional use without the

CONSUMER USE

Display messages relating to playback:

Display

Cause

NEW DISC

A blank disc is loaded.

NO DISC

An attempt is made to start playback

without loading a disc.

SCMS

–

ROM

button was

DIGITAL SYNCHRO

–

disignation.

Additional Information

Remedy

Take out the disc and check for dust, dirt, scratches,

etc. Clean as necessary.

Take out the disc and reload it label-side up.

If the same messages are displayed again after the

disc is reloaded, unplug the power cord and plug it

in again. If the same messages are still displayed,

please contact a Pioneer authorized service center.

Unplug the power cord and plug it in again. If the

same messages are displayed again, please contact

a Pioneer authorized service center.

Remedy

Record the source through the analog inputs.

Check that the digital input cable is connected

properly and that the power of the source player is on.

Check that the source is a regular music source.

Stop the source player. After a short time, 1-

is displayed, and the recorder goes into

SYNC

synchro–record-pause mode.

Wait until the message disappears.

While

is displayed, the recorder automatically

REPAIR

examines the recorded area of the disc and updates

the track numbers and recording time data. This

process takes about 40 minutes for a fully recorded

disc. Finalization or further recording is possible

once the

message disappears.

REPAIR

Wait until the message disappears.

Use another disc, or erase the

Load a

–

disc that is designated as

being for consumer use.

Remedy

Only recording is possible on blank

discs. Playback is not possible.

Open the tray and check that a disc is loaded.

Reference

p.9

p.15

Reference

p.25, 32

p10

pp.20–22

SYNC

p.19

–

disc.

p.8, 19

Reference

p.19

–

p.15