Pioneer PDR-609 사용 설명서 - 페이지 23
{카테고리_이름} Pioneer PDR-609에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer PDR-609 44 페이지. Compact disc recorder
Pioneer PDR-609에 대해서도 마찬가지입니다: 사용 설명서 (44 페이지)
페이지 인쇄
2
◊ÛB - >?/
AUTO
SCROLL
TIME
MONITOR
MANUAL
TRACK NO.
WRITE
AUTO
INPUT
ERASE
FINALIZE
MANUAL
SELECTOR
1
4,5,6
DIGITAL
ANALOG
REC LEVEL
REC LEVEL
PUSH ENTER
ANALOG
L
REC BALANCE
R
MENU/
TEXT
DELETE
SYNCHRO
CD TEXT
Legato Link Conversion
3
AUTO/
•
REC SYNCHRO
MANUAL
TIME
ABC
DEF
1
2
3
DISPLAY
/CHARA
GHI
JKL
MNO
4
5
6
SCROLL
PQRS
TUV
WXYZ
9
7
8
MENU/
MARK
NAME
3
DELETE
10/0
>10
5
4
¢
CURSOR
3
1
¡
ENTER
4,6
7
REPEAT RANDOM NAME CLIP
8
FADER
PROGRAM CHECK
CLEAR
I
NPUT
SKIP ID
SKIP PLAY
SELECTER
SET
CLEAR
1
Î
Setting the digital
recording level
One of the advantages of digital-to-digital
recording is that you don't have to set
recording levels—and risk distortion by
overloading the disc. If you're recording
commercial material from CD or MD, the
digital level has already been optimized
and you don't need to change it. If you're
making a digital copy of a CD, DAT or MD
that was not commercially produced and
that was consistently under-recorded, you
can boost the overall level by up to +20dB.
Remember though, that any peaks in the
original recording run the risk of
distorting the copy.
If you record digital satellite broadcasts,
you may also have cause to boost the
recording volume since the volume of
some broadcasts is relatively low, but
again, if there are any peaks in the
broadcast, you run the risk of momentary
distortion.
It's also possible to reduce the digital
recording volume, but in most cases, this is
not desirable. However, if you're putting
together a mix CD (various tracks
compiled from different sources), and
there is a track which stands out as
generally louder than the others, then you
might want to reduce the level of that
track. Note that this feature will not get rid
of distortion on the source material.
Once changed, the new digital recording
level remains until you change it again, or
reset it. Each digital input has its own level
which can be set independently.
: If you are recording DTS encoded
NOTE
audio CDs or HDCD format CDs, the digital
recording level must be set to 0.0dB for
recording.
4 Getting started
1
Make sure one of the digital
inputs is selected.
Pressing
INPUT SELECTOR
switches the active input:
Analog - Optical - Coaxial
The recorder's display indicates the current
input.
2
Make sure the recorder is
stopped, then press RECORD ¶
( ¶ REC on the remote control).
The recorder goes into record-pause. (You
can also press
MONITOR
3
Press MENU/DELETE.
4
Turn the jog dial until D. VOL
appears in the display, then
press to ENTER.
If there is nothing connected to the
selected digital input, the message
appears in the display.
UNLOCK
The display shows current digital
recording level.
Turn the jog dial or press 4
5
or ¢ on the remote control
to adjust the recording level up
or down.
• The maximum adjustment possible is
between
(silence) and +20dB.
MIN
• Pressing the jog dial (
holding for 3 seconds resets to OdB.
6
Press the jog dial (ENTER) to
confirm the digital recording
level.
repeatedly
.)
DIN
)and
ENTER
23
En