Pioneer S-LF3-F 운영 매뉴얼 - 페이지 2

{카테고리_이름} Pioneer S-LF3-F에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Pioneer S-LF3-F 4 페이지. Pioneer s-lf3-f: operating guide

페이지 인쇄

www.pioneerelectronics.com

CONNECTIONS

Switch off the amplifier power supply (OFF).

•

Connect the speaker wires to the input terminals at

•

the rear of the speaker; connect the common-side

wire to the · terminal and the hot-side wire to the

ª terminal. Bear in mind that the red input termi-

nal has a "ª" polarity, and the black terminal has

a "·" polarity.

Connect the wire to the loudspeaker outlet termi-

•

nals of the amplifier. Connect the hot-side wire to

the ª terminal and the common-side wire to the

· terminal.

Strip the insulation at the tip of the

wire and twist the strands.

10 —12 mm

If you insert the speaker wire too far so that the insulation is touching the

speaker terminal, you may not get any sound.

< right >

REMARKS:

• Check that the wires are securely connected to

the terminals. A loose connection may cause not

just intermittent or distorted sound but short-cir-

cuiting and breakdown of the amplifier.

• If there is too much exposed wire outside the

terminal, speaker wires may touch causing the

amplifier to short, damaging the amplifier and

making it unusable.

• If the wires of one of the speakers have been

connected with the wrong polarities, you will find

when listening to a stereo recording that bass

sounds are weakened and the stereo effect nor-

mally obtained between the two speakers does

not exist.

CAUTION:

The speakers are equipped with a protection

device to protect the transducers from extreme

conditions. Under these conditions the protec-

tion device will activate and stop the speaker

from producing sound. If this happens shut off

the system for 5-10 minutes and allow the pro-

tection device to reset.

Turn

the

thumbscrew

anti-

clockwise, make sure that the

speaker wires are inserted well

into the hole and turn the

thumbscrew clockwise to fasten

into position.

3 Connect the common-side

speaker wire to the

terminal.

4 Connect the hot-side speaker

wire to the

terminal.

< wrong >

USING THE ACCESSORIES

Confirm that the following accesories are in the

box when you open it:

2 Speaker stands + 1 polybag including 4 screws.

Before screwing the speaker stand 1 to the back of the

cabinet, thread the speaker wires through the opening in the

speaker stand and then connect them to the input terminal.

The 2 screws that hold the speaker stand must be screwed

into the dedicated inserts in the speaker.

2 Mounting panels

This Mounting panel 2 will enable you to mount the

speaker system on your interior walls. Before screwing the

mounting panel, make sure that wires are properly connected

to the input terminal. The 2 screws that hold the mounting

panel must be fixed into the dedicated inserts in the speaker

system.

Caution

In order to prevent the speaker from falling

make sure the wall is sturdy enough to sup-

port the weight of the speaker. Do not mount

it on plywood boards or soft-surface walls.

Mount the speaker system on a flat wall, this

will reduce the pressure on the screws, avoid-

ing the risk of become loose, and preventing

the speaker system from falling. If you are

unsure of the quality and strength of the wall,

consults a professional for advice.

1 Operating instruction/Warranty

NOTES:

Pioneer will not be responsible for any acci-

•

dents or damages resulting from improper in-

stallation.

CABINET MAINTENANCE

Use a cloth to wipe away dust and dirt.

•

If the enclosure is very dirty, wipe with a soft cloth

•

dipped in a neutral detergent diluted five to six

times with water, then wipe again with the dry

cloth.

Do not use thinner, benzene, cleaning sprays or

•

other chemical products on or near the enclosures

as the surfaces could be adversely affected.